ARGB Light Strip for Motherboard, 28 Independent Addressable RGB, 5V 3-pin Motherboard Aura Sync, Lightsaber-X Led PC Parts Kit Compatible with ATX

The AsiaHorse ARGB Light Strip integrates seamlessly with my motherboard’s 5V ARGB headers and installs easily. I’ve used these strips across four different builds, and they consistently deliver vibrant, even lighting that enhances the overall look of the case. The product feels durable, and compatibility with Aura Sync and Razor’s ARGB hub adds flexibility. Overall, these strips provide excellent value for anyone looking to add a clean RGB outline to their system.

easy to install, beautiful to look at, really the only matx one that i could find didnt have any issues with my io shieldafter installing these as its about equal in high to standard stand off screws for the mobo.

The quality is better than some reviews I read. I had no problems installing this LED bar in an old existing computer (30 minute total installation time). It's a tight fit but there are just enough clearances in my backup computer. It lights up well but I have an ARGB light hub so it has enough power. (I know low light output driver power can be a problem for some installations). So far, it doesn't have any problems. All LEDS light correctly. I will see how these LED strips hold up in 6 months and report back.

The 1st one I received was defective & had some flickering LEDs in the longer strip. Had to request replacement & send original back. Was a bummer as I made the assumption being new that there was no need to test it. So after installing the Motherboard in my new build & then connecting the ARGB strip did I then find it had an issue. So double the work to remove the mobo to pull out the bad set, pretest the replacement & then install the replacement. If your mobo has a metal support plate you may potentially have issues using this since this could throw off how your mobo sits at the rear intergal I/O panel to your metal RF I/O panel shield. Got lucky in my case it just eeked by without misaligning anything! It does however add a nice lighting effect! 9 mo update: 2nd one still working & looking fine!

Looks amazing in my computer

Sits under the motherboard so when it dies or glitches, it's a total teardown to pull it or replace it. Mine seemed OK until I tried to get a light count by painting the individual lights in signalrgb. The last two lights on the strip were 11 and 12, or 23 and 24, or 63 and 64. Doesn't make sense. Then they started flickering and choosing their own colors. Just junk. Don't bother.

Finally reviewing these after a long time, several LEDs have slowly dimmed and/or started producing off colors that don't match the others. They also stand off too far from my personal case so my motherboard had to be slightly... 'encouraged' to sit on top of them which was nervewracking but did not present any actual issues. Due to the LEDs losing their performance to such a degree over time I am knocking two stars off as replacing them would be a nightmare even if they were affordable to replace.

Why did you pick this product vs others?: Colors are there and does what I bought it to do. Understand that if you run a aio cooler or large fans the top may not be noticeable but it was easy to install and will be buying again. Mine is the large one and fit the ATX mother board holes perfectly. Argb 3 pin.

Looks and works amazing sync up with all my other rgb fantastical

Llevo ya al rededor de 3 meses y no ha dado ningún problema. La barra es muy buena, esperaba un material un pcoo inferior, pero me agradó demasiado que no fue así, el plástico para difuminar la luz de los LED'S es bueno y tiene una parte que supongo es de aluminio, se siente rígido, es de un tamaño bueno y encanja perfectamente con el factor de forma que elijas, yo pedí ATX y todo encajó a la perfección, trae una ligera capa de algo parecido a fomi para que no tenga problema con aislamiento. Es MUY BUENO que venga con incluso postes para la motherboard por si te hacen falta o no contabas con ellos, ademas de sus respectivos tornillos, eso me impresionó. En cuanto a los conectores, solo requiere el ARGB de 5V convencional y tiene una Y para agregar otro ARGB enseguida por si no tienes muchas conecciones, en general me encantó el producto.

Están un poquito caras, teniendo en cuenta que son sólo una tira con 15 LEDs (por lado) con un pedazo de plástico, pero en cuanto a estética queda muy bien para placas base que no tienen rgb. Si quieres erregebe para la mamalona es buena opción.

Easy to install, great lights... it just works.

Perfect brightness