LUSEE 2 Pack Clock Mechanisms Battery Powered with 13mm Short Shaft, Silent Quartz Movement kit with 5 Pairs Aluminium Clock Hands, Hands and Motor Mechanism Replacement Kits for Repair DIY

Absoulutley perfect for my newish clock or indeed for a replacement part for an older modle . The variety of hands to use gives you more choice colure and length. with the spare clock and hands will make a clock out of some old palets for the garage or garden wall.

Did not realise the size of the hands, had to cut back, and coverup the cuts with a black marker pen.Really wanted mechanisms without second hand, and a slower tick to increase battery life.

Worked well easy to fit

Over time battery clock mechanisms can become unreliable or stop working altogether. In my case this was after 10 years by which time a replacement of the same design was not possible. Rather than throwing the clock away and buying another it was very gratifying to be able to repair the clock rather than getting a replacement. It was also a much cheaper option. Many modern wall clocks use standard sizes of timer unit, and it is really a question of finding the right one to fit an existing clock. This kit comes with a decent selection of hands which fit the timer unit and which can be trimmed to size to some degree if required. The stem/shaft which supports the hands can be of different lengths depending upon the size of clock so if replacing an existing unit it is important to choose the right kit in terms of shaft length. The diagrams on the product details have sizing details for assisting with this.If replacing an existing unit make sure to measure the length of the pillar supporting the hands from the back of the plastic gearbox to the tip of the pillar. For this kit the product details show dimensions and this distance was 13mm. If this pillar/stem is longer than the original unit there is a possibility the replacement will not fit under the glass of the clock case. Although it may be possible to use washers to set the gear casing back from the clock face it is better to get the replacement size correct to begin with. Likewise, any existing hands will need to fit on the spindles of the new timer unit.The kit comes supplied with a variety of different sizes and shapes of hands. The hands are very delicate and are neatly wrapped in protective plastic sleeves. Hands painted black have a film of plastic to protect the surface. This should be peeled off before fitting the hands.To trim any hands that are too long use a knife or other sharp edge to push into the surface of the soft metal hand at right angles to the length. The scoring will then easily snap off with a little pressure applied and should leave a clean edge.I was very pleased with this kit – it took me approximately half an hour to repair a clock which had become unreliable (the hands kept slipping backwards losing time). It is actually a very quick job if you know what you are doing but I was trying to be careful.For £6.59 to repair a clock that was no longer available to buy (and also cost much more) this was a very satisfying repair. The fact the kit has two timer units is a bonus. Very good value.

The media could not be loaded. Good value at £6.99 for 2 mechanism and 5 sets of hands. Very easy to fit, comes with instructions if you need them. Just take care on seating the arms properly and check they don't touch and that's it.I like the sweeping second hand but you don't need to install it.Silent operation so suitable for bedroom.Timed it for 9 minutes and admittedly I was a bit slow to stop at the end so 9.00.67 is OK,I'll report back if it loses/gain over a longer period. Happy with the product. Might use the 2nd mechanism to make a clock with a picture in a frame.

I have been looking at clocks around the house that have been on stop for years almost. I have bought these and repaired 2 clocks. Great, smooth sweeping seconds hand, quiet and are keeping good time. Would buy again definitely.

repair clockdownside was delivery person left the gate wide open , we have animals!!!!!

Got these to replace the mechanism on a 30+ year clock. The second hand proved to be too long but it cut back easily. Works fine.A bonus came when my brother asked if he could try the second mechanism in one of his clocks. It too worked well - so two clocks with one order Really good value.