MINDCOLLISION Sport Ball Inflation Valve Kit(20 Pieces), Basketball Valve Replacement Valves, Sports Ball Leak Repair Kit,for Basketball, Football, Volleyball,Soccer,Matchballs

I was not looking forward to changing out the valve in my basketball, but I watched a video and decided this was something I could do. This kit worked great! I have extra valves for the future now too!

Had 15 Tachikara volleyballs with dry, brittle, leaky valves. These replacement valves gave the volleyballs another lease on life! The removal tool made the job of pulling out the old valve so easy, and a tip holder made it so easy to push the new valve in. I waited 2 days to leave a review, and, YES, they are still holding air!

The valves are amazing. VERY easy to install. So easy that I thought I had done something wrong. The valve puller that comes in the package, however is awful. It does not work. I ended up using a crochet hook to get the old valves out. That worked well. I should have used a slightly smaller hook though, because I accidentally pushed some of the old valves into some of the balls and my girls soccer team now hate using those ones because the rattle. Maybe lube the hook too, to ensure that the hook goes through the valve all the way before trying to fish it out. I have no idea how the get the ones I mess up on out.

Excellent product!!!

So glad I purchased this item. Replace my first valve tonight. Using it on volleyballs for my school team. The picture shows the old disintegrating valve I removed next to one of the new ones. The removal was easy. I used the tool in the kit and it pulled it right out. I used glycerin as the lubricant. I read it was the best for inflating balls. Putting in the new valve was harder. I used a small pair of needle nosed plyers and grasped the valve just on top of the fat part of the valve and pushed hard. I will do more balls tomorrow. I recommend this product.

The extraction tool is worthless. After watching the provided how to video (and others online) I tried 6 times very patiently to replace the valve on a soccer ball. Every single one fell into the ball and the last one worked for a day and then leaked the next day. Bummer. Don't get these.

These did not work on a football. As others have mentioned, the extraction tool that comes with this kit is not good. I would definitely get a crochet hook or the old stem has a much higher chance of falling into the ball. These valves were nearly impossible to get into the ball then it wouldn't stay after finally getting it through the opening.

I replaced my old plug with a new plug. It took a lot of work to remove the old plug the tool they give in the kit, the hook isn't very good.Putting the new plug in takes a bit of work. DONT CUT THE EXCESS PLUG off to soon fill with air to see if you have any leaks.You may have to push it down more to seal the plug. That was my mistake and had to replace the plug again cutting it to soon.(What sticks out from the ball)

Excelente

I really liked the valve kit. I had tons of old volleyballs from the school that were all leaking and fixed every one that only had a valve leak. Steps: firstly fill a sink with water, fill the ball and check for where the leaks are. This will only repair a valve leak so if it leaks anywhere on the seams then you will have to look elsewhere for how to fix. I just turned the balls into hats by slicing them up for school supporters. Once leaky valve is found, use the hook tool and pull them out at an angle, like you are digging them up using the hook. Once out. Use a 1/4 inch driver to put over the new valve. I needed to cut the valve stem a bit shorter so the driver would come down further over it. This was no problem as I still needed to cut the valve stem down afterwards even more once inserted. Then just push it straight down into the hole until it makes a slight pop sound and feel. I actually put a small bit of silicone on it to make it glide a bit easier but they are already a bit slippery anyways. Now you can pump up the ball and then slice any part of the valve stem that still sticks out past the exterior ball surface. Mission complete. I used this with volleyballs but the same configuration will be on soccer, footballs, rugby, handballs and basketballs.

El kit está muy bien trae lo necesario

My molten volleyball was under inflated when trying to replace the valve with the provided tool. The valve ended up falling into the ball and took quite some time to retrieve with needle nose pliers. Once that painful extraction was complete, installation of the new valve was very easy and no leaks.

Revolved a few and all have worked. Toughest part is the removal.