Abahub 236 mil 16 sqft Car Sound Deadener Hood Firewall Heat Shield Insulation Pad Automotive Sound Deadening Mat Aluminum Roll 59"x39"

Worked as described. Would buy again

My 2000 Toyota Camry LE's OEM Hood heat shield insulation/deadener started deteriorating and pieces of it being peeled off so i decided for a DIY replacement project and bought this Abahub 236mil 4x6 (16sqft - measured first the size of my OEM Hood heat shield as there comes options in sizes). The package came at a very good condition nicely packed inside a plastic and rolled. I inspected the product as there were some reviews about damage/ripped aluminum foil and I am glad mine came in without a damage. Carefully unroll the sheet on a flat surface ( i used my garage floor) and gently flatten the surface (aluminum side facing the ground to prevent damage) and once evenly flat, flip the sheet aluminum now facing up and let it rest and prep for cutting to size matching the OEM from the car. I used sharpie pen to mark the holes and exact size to cut and I just used a medium size office scissor (very easy cut) don't use box cutter it would create a tear to the insulation padding and rip off the aluminum if dragged. There were 11 spots i marked for the location of the round push in clips (when i removed the 11 clips all of them broke and no longer usable but i always keep many clip parts for my vehicles). I was only able to get 4 out of 11 push clips to match the holes when i applied the insulation to the hood (not to worry, the backing adhesive will do the job to hold it together. OEM does not have backing adhesive, it was hold in place by the 11 push clips to the hood) I started from the top which matches the exact location of the top 3 holes allowing me to work without an extra pair of hands. I didn't push the new round clips just halfway and enough to hold the insulation sheet allowing me to access and gently peel off the backing adhesive cover to expose the adhesive part of the sheet. Worked my way from top slowly applying pressure to stick to the hood back surface and making sure the insulation sticks to the surface making sure there is no gap/air. Tip: if during the install, you accidentally damage or rip off a part of the aluminum heat shield, you can simply patch it with an industrial grade aluminum tape (commonly used in HVAC install/repairs). Ultimately, this product can be to cut to size, easy to install with enough thickness and insulation for heat and reducing engine sound/noise when driving the vehicle. I highly recommend, this product won't disappoint you.

This product is very well made and definitely high-quality. There is a kind of a string material laid into the aluminum backing which prevents it from overstretching and tearing. I found this to be very useful when installing considering I was walking on it and kneeling with my knees I never had an issue of tearing the glue is very strong so make sure you know where you're putting it because you won't be able to lift it up without destroying the foam. I use this to insulate a transmission tunnel and the entire floor of my vehicle there is absolutely zero heat radiating from my carpet now .The paper backing was hard to take off initially but I took the roll into my driveway and rolled it out completely paper side facing up in the Sun and 20 minutes later the glue was soft enough to easily peel the entire paperback off. So if you have issues peeling the paper just roll it flat and make sure you pull carefully because the the paper easily tears.

I used this insulation material along with butyl sound-deadening adhesive mats to insulate the interior of my vehicle. My goal was to reduce the drone of the exhaust. Overall, this insulation material, along with the butyl sound deadening, helped to reduce the interior droning noise. As other reviewers have stated, this insulation is very sticky. One thing that I did not like about this product is that the brown wax-like paper used to cover the adhesive until use was very finicky and did not come off cleanly. Often, when removing this paper just before installation, it would not come off uniformly and would tear randomly, leaving small remnants on the adhesive side of the insulation. I think that if a thicker or better-quality adhesive-protecting paper were used, it would improve the installation experience.

I purchased this for a heat shield under the passenger seat of my 2010 Polaris XP900 as the seat gets extremely hot while being operated. So far on short trips, the product has worked extremely well with the seat being warm and not hot! The product is very maleable, but also extremely sticky; so it’s important to make sure you’re sure on you placement before pressing it down. Overall, I am extremely pleased with this product and the price I paid for it!

Really easy to install. I used the original liner as a pattern, cuts with scissors.

Make sure that you have this where you want it before sticking it down. It sticks well, but if you need to pull it off to reposition it, it will rip and leave part of the mat. It does stick very well, so hopefully I will never have to remove it, otherwise it will be a big mess. I haven't run the engine yet to see if the noise level is reduced, but hopefully it will lower it.

used it for my car for under the hood for dampening , it is holding up real good , no problems

Quality of product not good upper aluminium foil tear out

Lo instale en un auto antiguo y fue muy útil. Redujo el ruido exterior significativamente

è un buon prodotto

Gute Qulität superrrrr!!!

Pretty good universal size, cut to size and was easy to apply. It is so sticky that you will have some on your hands. Require little skill to cut and install