ACANII - For 2005-2011 Toyota Tacoma LED DRL Halo Ring Black Housing Projector Headlights Headlamps, Driver & Passenger

I installed these headlights on my 2010 Tacoma, and by taking my time with the wiring, it wasn’t too difficult. They turned out looking great. Here’s how I did the install: 1. Gather all the black wires from the back of the new headlight and combine them into one connection. (I attached them to a male contact point.) 2. Gather all the red and white wires from the new headlight and combine them into one connection. (Again, I used a male contact point.) These will eventually connect to the DRL (daytime running lights). 3. Locate the DRL wiring on each side of the vehicle. You’ll find a green wire (ground) and a black/white wire (hot). 4. Splice a connection into each wire so you can connect the grouped wires from the headlights. (I used a simple quick-connect with a female contact.) 5. Connect all the black wires from the headlights to the black/white wire (hot). 6. Connect all the red/white wires to the green wire (ground). 7. Test all functions to ensure everything is working properly, then reassemble. Tools you’ll need: • Quick connect/quick splice wire terminals • Crimping Tool While it might appear to be overwhelming at first, it’s rather easier than it looks. The lights seem plenty bright for me, but I’ve only had them for a short time, so I can’t speak to any potential issues yet.

So twi things when purchasing these. 1. These are manufactured by Spyder and model number is 5011916. 2. Toyota tacoma 2010 running lights only have 2 conductors so its easy to install. So i called spyder there in pst zone. They were helpful and answered my questions. However you install it be sure you pair red and white together, and all black wires together -so you should have two groups of wires. You’re splicing cables from the running lights. On my vehicle i have green and white & blue. White blue was negative for me. I did switch around to find out. I used lever nuts and solder which all worked. If you want to test twist the conductors together and test on the car battery. Leds are 12v so you can test the headlights before fully installing them. I love the look and look bright but the LED are not that bright but do the job of running lights. They look the same from the pictures. I would buy from the seller cheaper than most from others out here on amazon. Don’t buy stock ones but these. Either from here or spyder. Hope it helped.

Why did you pick this product vs others?: Best lights I have ever installed on my truck. Perfect fit and great look. They work as intended with no issues. I would definitely buy from them again.

These headlights look great, and also put out great light. This is the second aftermarket pair of headlights that I’ve put in my 2011 Toyota Tacoma. I poured about half a gallon of water out of the last pair, which is why this time I reinforced the seams with synthetic silicone. Wiring isn’t too difficult, but takes some splicing to wire the LED lights. Simply splice the wires to the positive and negative wires for the parking lights (top, outside corner light). I spliced all the LED wires to the parking light in one big connection, but suspect a daisy chain may have been cleaner. If I was to do it again, I would cut away the excess LED wire length as to avoid the rats nest of excess length that I was left with. Following install, adjusting the lights was straightforward with lots of room for adjustment provided.

I like the way they improved the look of my truck. The wiring instructions could have been better; it took a little while to figure out how to get them wired up correctly. They worked well for a while, but eventually the LED light strip on one side stopped working. After having them for a while, I have noticed condensation after a wash, but it does go away; however, they oxidized and started getting a foggy look too quickly. Overall, they look good, fit well, but the durability could be better.

I wanted to spruce up my 10 year old 2010 Tacoma. Just compounded the paint and looking for new lights. I ordered these Acanii headlights. It looks just like the Spyder PRO-YD-TT05-HL-BK that I had looked at on two other sites. I had planned to use a automotive products website because of the technical support, but after chatting with two sites, I realized that their service was very sub standard (they were delberts). I ordered these Acanii lights and received the Spyder PRO-YD-TT05-HL-BK lights! $139 compared to $195 on the "other sites". The warranty is 60 days on Amazon compared to 1 year on the "other sites". Installation was easier than re-installing the original headlights. I did break some of the plastic Toyota clips and will need to replace them, so it would be a good idea to buy them in advance. Wiring was pretty straight forward wiring the led's and halo's to the parking lights. I did ask the question here if the daytime running lights could be still used and YES, they still function. Just installed them and they look super! Haven't adjusted yet, but so far, very happy with the look and the purchase!

I had bought another cheap pair months ago and the light output was dismal and scattered. I popped these in after wiring all hots and grounds to the parking light wires, and turned them on. Ten times better light output ! And they are adjustable. I still have to tweak the horizontal, but vertical is perfect. They don't blind everyone else and I can see in the morning at 3:30AM when I go to work. The high beams are astonishing ! Awesome upgrade and the halos and LEDs make them even better !