Shadeidea JT Sun Shade Top Sunshade Compatible with Jeep Gladiator Top Shade Mesh Screen Roof Cover (2018-2023)- Wind Noise UV Blocker with GrabBag Pouch -10 Year Warranty- Black -Front+Rear (2 Pcs)

Great design/construction, and not too hard to install. I was able to attach it with the rear hard top still on my Gladiator. It is a little tricky to operate the latches on the forward panels, but I got it figured out.

This item came packaged well, great instructions, and great quality, especially at the price point! Everything was clearly labeled and the instructions were fine.The "Fold paper as a driving strip" broke immediately as I expected. I doubt that it would ever survive the multiple bungee cords it is meant to help feed. Do yourself a favor and just remove the 4 bolts needed to lay the windshield down and just lean it out a bit to feed the windshield bungees. I did this all alone but please make sure if you decide to lay the windshield completely flat to also remove your windshield wipers.I was concerned with the hard top fitting with this sun shade installed. I'm glad to report that it will fit, however if you are on the taller side, your head will touch the sunshade WITH THE HARDTOP INSTALLED, I've had no issue with that with the hardtop off. If you remove your freedom panels only the wind noise is amplified with this sunshade installed but WITH THE HARDTOP COMPLETELY OFF, the wind noise is very minimal which is overshadowed by the excellent job it does to block you from so much sun exposure.I saw a couple of review about the back of the sunshade flapping in the wind. I initially had some slack that would have allowed that, however adjusting my bungee straps around tightened it up and I have had no issue.I've seen complaints about the use of the bungee cords over other attachment methods. Honestly I would rather have the bungee cords as they're cheap and easy to replace if needed.

22 Gladiator full length shade: This shade is super easy to install. I would strongly suggest removing the 4 bolts holding the windshield and it’ll make everything much easier than using the supplied paper “tool”. Just tilt the windshield forward enough to get the bungees through and adjusted.Also, use the picture on the back of the instructions instead of the wording. Much easier to understand. Took less than 15 minutes to install it. Blocks the sun as well as my previous mesh shade but this one wraps all the way down below the rear headrests. PERFECT to keep my daughter out of the sun and even calmed the wind down inside the cabin.The spare pouch for my use can’t be used unless I want my passenger with it resting on their legs. The case the whole kit comes in is nice as well. Another tip, get it on, adjust it as best you can then readjust after it’s been sitting out in the heat for a while. Also may take a few minor adjustments as the material relaxes to get the fit perfect.

Looks great, slightly reduces headroom, some noise but better than expected. Installation was as expected, but the bungees tight fit are the reason flapping and noise is not too bad.

Had no problems, the only thing was the paper to pull the straps with will break, I just added a little duct tape to it. Perfect for what I wanted....definitely recommend!

Great product..keeps the direct su n from burning you..easy install

Easy to install. Well worth the money.

It was a bit of a challenge deciphering the pictographs for installing this shade. Once I figured it out, it was nothin but a thing. The little paper for pulling the cords through is a bit in the weak sauce side, but I understand keeping down costs to meet margins and all. I have it a chance, and it worked as designed. In the future, I’ll make a utility tape version of the threading paper instead of using the included paper one. A bit more instructions and a more clear step-by-step cord placements would help other, future purchasers and installers. You just have to feel around for the correct places to slide the cords through. If you test feed from the reverse side, you’ll be able to find where to feed from the top side down. (Sounds cronky, I know, but it worked for me).The shade gets in the way of roof lever access, but you get over it. It’s a small trade off. But the shade is nice, because you can drive around the city and have just a tiny bit more peace of mind, knowing that it’s going to take someone slicing through your shade and making a scene, to get at your truck interior (when your tops are off), and that’ll buy you a bit of time to catch the dirtbag pawing at your truck goodies. Just don’t be a dork and neglect making sure you don’t leave valuables in easy reach.Overall, this is a nice shade, it’s inexpensive compared to making it yourself, and it comes with an extra do-dad for your grab bar.Only 4 ⭐️s for the reasons my reasons listed above. As for durability, I’ve worked with this material before, and I know with TLC, it’s going to last a good many years.