MOOG Front Suspension Track Bar Suspension - Professional Grade Ball Joint Replacement - Gusher Bearing Design for Smoother Steering - Pre-Installed Boot Shield

Problem solver ball joints . I wanted greaseable ball joints . These moog also have a better boot system . They fit well and were easy to install.

Good fit and look well made. i used on a 1999 silverado and the project turned out well.

Fit my 05 sierra. Moog is always the way to go with front end parts. Highly recommend these ball joints. Cheaper than the parts store moog products

Good quality. I’m only buying Moog ball joints from now on.

Moog is one of those legendary brands that you know your going to find quality in with whatever your replacing. Moog is my go too for anytime I have to replace suspension parts. They are designed and built with perfection. They always fit perfectly and go in easy with everything I’ve ever replaced sometimes they can very a little bit from factory parts but the Moog ones always seem to be built more heavy duty then the factory parts. Plus the grease inserts make them worth the money. The durability of Moog will not dissatisfy you. Please always make sure you have an alignment done anytime you change any suspension parts no matter how minor.

Perfect fit on a 2007 Silverado 1500 2WD. The OEM ones are a pain to remove, but these insert very easily with a ball joint press. The fact that these are serviceable mean that they should last a very long time (unlike the OEM). They are built very sturdy. My one complaint was that AFTER the installation was finished and everything was put back together, while filling with grease, one of the ball joint dust boots had a hole in the side, so as it began to fill with grease it just squirted out the side from a location that would not likely have been damaged during installation (the dust boot is retracted inside the steel housing until you fill it with grease). I contacted Amazon and they are sending a replacement. I would recommend doing some kind of inspection before you install to prevent completing the job only to find out that one is defective.

Bought this for a front end rebuild on a 2011 Tahoe 4x4 GSA package (basically a LT with police trim) and it was a perfect fit, went in exactly like an OEM part. Steering and ride are MUCH improved.

This is a textbook example of why MOOG is trusted in the aftermarket segment. The K6541 ball joint is over-engineered, featuring an impressively thick stud and pre-greased housing. Installation on my Silverado 1500 was smooth, with tolerances matching perfectly to the control arm cavity. Performance after 2,000 km: Zero noise, tight articulation, and no grease leaks despite off-road conditions and heat exposure. The zerk fitting provided ensures easy periodic lubrication, extending lifespan significantly. Critique: None from a mechanical standpoint. However, the supplied castle nut could be improved by adding a corrosion-resistant coating, especially considering regions with salted roads. Overall, a solid, fail-safe upgrade for trucks operating under load or rough terrains.

Installed the Moog K6541 into my 2016 GMC Sierra 1500 Denali, which has the cast iron control arms. These fit well and seem to be built strong. Replaced my worn out stock ball joints with 155kms on them. They are genuine MOOG and are greaseable. Using a ball joint press tool made the install very easy. I did both sides in 2 hours. Torqued to 37ft/lbs +130* as per oem spec.

This Lower ball joint fits 2002 GMC Sierra 1500 with 4x4, Good quality and really stiffens up front end. Moog is one of the best when it comes to suspension parts no doubt!

Fit my 2013 Silverado 1500. Double check the part on the moog website before ordering. Didn’t get any torque numbers with product or from website. Website gave me a number to call. Didn’t call got torque from other source. Both boxes were damaged in amazon package with rip in it. Didn’t lose any parts. Came with 90 degree grease nipple nut split pin and spring clip. Hopefully it lasts.

Très bonne qualité je le recommande vivement

Ok sur mon Silverado 1500 2016 avec table en acier forgé.