Dicor RP-CRCT-1 EPDM Roof Acrylic Coating - 1 Gallon - Tan - Long-Lasting and Durable

This product was used on an original 2005 Fleetwood Fifth Wheel rubber roof that was in pretty bad shape. Overall, this product worked amazingly! Prep and application are very straight forward, as detailed on the can (also watch YouTube Video-RV Rubber Roof Coating System by Dicor. My only challenge was to get it all done in one day- Applied on a fall day and time to complete was close to ensure enough light remained in the day. Make sure you start as early as possible to ensure you get the 2 coats down. The product applied easier than painting the walls of a room. I did not notice a strong smell and the flow and coverage was really good not sticky- used a roller and paint brush as needed. I ended up purchasing 3 gallons for my 30 ft rig. Two gallons may have sufficed but I ended up applying the 3rd coat the next day-probably overkill, but worth it to me as this roof did not have much left on it and it gave me peace of mind. At the end of the project, I found that the roof looked almost new. I did not notice any cracks or lesions in the roof as the material covered them very well. This product will not solve any issues with roof edges lifting-I used EternaBond Roof Seal Sealant Tape to tackle and concur the edges. This product worked really well, better than I expected and saved me from replacing my roof.

Easy to apply and looks great to our older RV!

I had previously ised dicor self level lap sealant to replace my vents and used dicor non sag for trim and seams and to create a condensation/rain run off channel. I skipp3d stage 1. Wasnt a fam of the cost for a quart. I woke up early and scrubbed the roof with a soft car wash brush, Warm water and blue dawn dish soap. I then used a high pressure nozzle on my garden hose and really hosed it all down until the water ran clear, no more grey water or particles visable. I then used a soft bristle broom and swept the water off. And towel dried any spots with a little pooling, I wated until everything was dry, about 40 mintues on a 80 degree day. I then started a thin coat at one corner pouring some out and using a 1/4" nap roller applied until the roller hissed when rolling and added more paint. While waiting for that to dry enough to walk on. I went around the edged and did the trim with a 2" brush. Coat 2 I laid on thicker. Then did more trim coat 3 was thick then Inused the bit left over to apply to areas of water pooling and seams. All in all, it was about 5 hours total with some breaks and even a run to my LHS for more paint thinner. This stuff has a odd odor. Like industrial silly putty. Its thick. Like honey or cold maple syrup. Easy to work with. It wont run unless you pour out too much. Keep mixing ans you wont have the gallon skin up on you. If you take a break, cover it with a wet T shirt or rag to stop it from drying uo. If working from the can, get a pour spout snap on lid. It will keep thr can clean when moving around. This stuff cleans up easy with paint thinner and a good microfiber rag. A+ would buy it again!

Good product. My 5th wheel roof was in bad shape. 12 year old trailer uncovered parked next to house. I worked cleaning roof two hours per day for three days in the early am due to 102+ degree heat. On the 4th day I sprayed the cleaner activator with a new garden sprayer and pressure washed it off after waiting a half hour. There was still a lot of crud on the roof. I ordered more activator and then on my hands and knees I used a small hand held spray bottle. I waited another half hour and pressure washed again. I'm a bit of a perfectionist, and was never happy with how clean the roof looked. After the roof was dry I recoated the roof in three coats of the rubber roof coating. Due to the high heat the coating was trying to dry in the roller pan so there are a few lumps ( not many ) on the roof. Roof is now a bright white and looks like new except where I got some of the coating an the AC lower cover. One thing.....Watch the Dicor Video on the internet, install the plastic sheeting, it protects the trailer sides. The video does not warn you of the mess around the trailer the old coating creates. Took hours to clean that up as well. Be advised, This was a bitch of a job ( I'm 73 } no fun at all, but had to be done. As soon as I'm sure the roof has dried thoroughly I intend to cover it with Dicor protective coating. My wife and I are traveling to the Midwest in September so I'm hoping I did it right and it holds up well.

I watched the videos, read the directions, and read the reviews. In the reviews that weren't positive, it seems the directions weren't followed correctly...what did those people expect? Over the period of a few days, I completed this project with the help of my 15 year old daughter. We set out to do this in 1 day. If we didn't live in South Florida, it would have been possible, but our humid weather affects drying and curing. We did this in November when our weather was far less humid than in the summer. We got the 28' trailer covered, roof cleaned, and 2 coats of roof coating completed within 1 day. Finished by about 4pm. The following day, the roof was still a little sticky. Dry to the touch, but sticky if I walked on it. After a couple days, it fully cured. We wanted a 3rd coat to even out a few areas and because we still had enough product to complete another coat. 4 days after, I swept off the roof and applied the 3rd coat. It was fully dry and cured by the following day. This coating covers the rubber roof well and I believe will stop that weird white/black streaky stuff that runs down the trailer and creates the streaks. Be sure to fully cover the sides of your trailer before cleaning. We used a roll of visqueen and frog tape from Home Depot. Lots of yuck comes off the roof. I didn't have a pressure cleaner to use on the roof, so I scrubbed it with a long-handled brush and a high powered hose attachment after letting the cleaner/activator sit for about 30 minutes. A little of the crud washed off the roof seeped through our covering, but not bad. After rising and rerinsing and then rinsing some more, we pulled off all the plastic covering and rinsed the sides at the roof dried. Tedious process, many trips up and down the ladder, but not difficult to use and performs as desribed. We used 2 gallons for a 28' trailer.

Great product. The only drawback was dicor states to use way more than you actually need.

Great value for the money, easy to apply, is durable and of adequate thickness to do a great job covering the roof.

Easy to apply good product

Ohne primer geht nichts also eine kleine Rolle und los geht es.haltet euch an die Vorgaben primer und zwei anschließende Anstriche in 24h.

igfd7tf

We had this put on our trailer roof when we purchased it. We had a man come today and it is peeling and he had to repair it. I would not recommend anyone purchasing this product.

Product arrived quickly. Used 2 part system, cleaner/activator, and Dicor EPDM rubber roof coating. Easy to stir, rolled on easily and smoothly. We were able to do 2 coats after applying Dicor cleaner/activator, and rinsing/pressure washing off, letting roof dry, in one day. Very impressed with the finished roof. Looks new again. It’s been on for a week, and seems to be a durable finish. We’ll know more after a Maritime winter but so far, very happy with this product.

The products are fantastic and very easy to use. The roof looks good and very white... This is the second time I use the product (approx. 5 years ago) and it lasts very long without and pealing or problems... good product