Koss ポータブル交換用クッション、ブラック。

KOSSのporta proを長く使っているとイヤパッドがボロボロになるので交換 2回目ぐらい 同じようなイヤパッドはいくつもあるけどやはり純正品ということで

やっぱり公式を買うのが1番ですね！カラフルなのを買ったことあるけど穴がデカくて外れやすかったりサクサクした素材で一年弱で経年劣化でポロポロ崩壊してきてびっくりしました。 でも公式で色んな色出してないですよね？ 見つけられなくて。。 自分は黒でいいんだけど需要ありそう。

数年でKOSSヘッドフォンのパッド部分がボロボロになり、その後100均のパッドとかで交換したがしっくりこず。 長いこと放置してたのですがこの製品を見つけ購入しました。 まぁ値段はそれなりにしましたが、一度交換すれば数年持つのと、失敗するかも？という不安も無いので満足してます。

ビックリするほどボロボロになります。ただ、サードパーティ含め保守製品は豊富なので良しとしましょう。安いですし。

しっかりしてる

純正品で6個入りのため予備も安心。 価格も安価でサイズもピッタリです。

着けるの簡単

汎用品と迷いましたが、内径サイズが小さいとリッツ線？に干渉するかもと思いこちらを購入しました。価格は高いですがサイズがピッタリなので良かったです。

These foam ear pads seem fine, but I struggled to figure out how to install them on my Koss KTXPRO1 Titanium headphones. The original foam pads had deteriorated to almost nothing after a few years even though I don't use them often. I found it easier to work with by first removing the speaker part from the head band; gently pry the speaker part from the two pivot nubs of the head band. Work on one side at a time so you don't swap left and right speakers. I could slip the tip of a flathead screwdriver between the inner black plastic speaker part and the outer plastic silver enclosure, but it did not snap apart and felt like I might break something if I forced it. Actually it does snap apart, but there is a dab of stretchy adhesive on the center junction where the two parts snap together. Use a fairly wide flathead screwdriver so that you can twist it to create a big gap. Work your way around with the screwdriver until you have loosened the hold of the adhesive and created a large enough gap so that you can grasp the black plastic part with one hand while holding onto the silver enclosure part with the other. Gently twist a little but mostly pull it apart until it breaks free. See the image for how it looks when you get it apart. You might pick out any excess adhesive that may get in the way of reassembly. Pull or cut out remnants of the old pad and replace with the new pad. Gently tug it into place, and push your finger along the surface from the center to the edge to help evenly distribute the new pad so that it covers the spiky nubs. To reassemble first make sure that the rubber cord strain relief is wedged in the notch on the silver enclosure. Then align the fastener part on the back of the black speaker with the corresponding part in the center of the silver enclosure. It is challenging to tell if you have it aligned correctly, but with visual approximation and a light touch you can do it. Making sure the wire is not going to be pinned in the center snapping fastener, press firmly and it will click into place.

Exactly as I expected. These are the real thing, fit perfectly my Koss PortaPro. Well worth the price.

Good product!

Conforme à la commande sans surprise

Excelente, produto original e o envio foi super rápido