VEVOR Ultrasonic Cleaner 1.3L Professional Ultrasonic Cleaner with Digital Timer 40kHz Excellent Ultrasonic Cleaning Machine 110V for Jewelry Watch Ring Coin Diamond Eyeglasses Small Parts Cleaning

I bought this 6L capacity cleaner because I had a 3L before and it really wasn't big enough for anything but small very carburetors. The 6L can accommodate decent size carbs and I mean plural because you can clean 2 or 3 at once, depending on their size.That said, I did some measurements and the tub does not match the dimensions advertised, it comes in at 12.8"x5.9" at the top and is tapered toward the bottom with depth of 5.9". However, since it is not a perfect cuboid/block, it holds only 5.5L of liquid to the very top. The recommended fill line puts the useful capacity only at 4.5L. Now as for the basket, its measurements (averaged readings from both ends of each dimensions) come in at 25cm x 11.5cm x 8.8cm (for ease of calculating) which puts its volume at 2.5L.The supplied drain hose is nicely flexible and 30.75" long and it comes with a fitting to screw into the drain (ball) valve. Silly thing: while the drain valve utilizes the standard British NPT 3/8" threads, the plastic fitting has a metric pitch of 1.25mm/thread. (see picture)Having the drain valve on the unit is very useful given its capacity but once the tub is drained, it is best to dump any remaining few milliliters by flipping the cleaner upside down because the tub bottom is not sloped toward the drain and as such does not allow all the liquid to flow out perfectly .(see picture. Word of advice: it is best not to empty the tub perfectly by shaking every drop out (with the drain valve open) because only the tub is stainless, the drain is not. And it can rust after just one use. (see picture)I like the little stainless steel ball enclosure for small items but its size (just over an inch) does not allow too many items inside, maybe 1 ring or a few short screws or carb jets. I would have preferred a bigger one but since it was a nice extra surprise (not advertised in the listing), I am not complaining.The parts cleaner is powered by a 5ft standard grounded cord.The control panel is clearly labeled, allowing for operation without having the read the user manual every time. (Though the up/down buttons are reversed, as has become the norm with Chinese designs)The control panel digits are nicely bright to read even in direct sunlight and so are the ON indicators for the heater and sonic elements, even though that the indicators are visible only from a limited angle straight ahead. Buttons have a nice and crisp feeling and the panel beeps loudly with each press. The default temperature preset is 50°C and default (longest) time for cleaning is 30 minutes. It would be nice to see maybe 60, 90 or even 99 minutes. That would eliminate the necessity to have to come back and restart the cycle for another 1/2 hour.The heating element could be a little stronger, 50W takes a very long time to heat up a full load. Specifically, a tub full of water at room temperature takes a whole 1/2-hour cleaning cycle to get up to the default preset 50°C.As far as noise levels, they aren't high. Certainly louder than the 3L cleaner I had but acceptable and not really noticeable in a work shop with tools going. I like to hear the thing buzzing anyway because at least I know it's running. When it stops, even if I miss the two loud beeps, I will notice later that there is no noise and I know the parts are done.Overall, even though the advertised capacity is above the actual capacity, this cleaner can still accommodate plenty of parts.

This cleaner is a beast, I had the smaller cleaner from the bargin tool store and honestly it worked pretty good but this cleaner is in a whole new level. It litterally forms little waves from the constructive interference lol. It is a great size, I have put holley carbs in it and it does great, of course Id still break them down before cleaning and blow them off with compressed air to keep your cleaning solution from getting instantly filthy. It is made of stainless which so far seems plenty tough. It is loud though but its naturally going to be, if it wasnt Id be concerned. Its has good stability and doesnt walk around or do anything weird like that. The drain valve and little screen thing in the bottom of the tank are awesome, I always had to flip my old one and sometimes water got inside and it didnt work quite right after that. It cleans parts very well especially if using the proper cleaning solution.The only con there is and I think they all suffer from this is if you are not carefull when filling it you can get water inside of it by running down the sides, mine still worked after this but it kept setting of the gfci plug until it dried out. When I got mine it was at an excellent price.

I don't usually write reviews but on this product I feel one is warranted. I am a dyi home machinist, metal fabrication, welding, and automobile enthusiast. It seems like I am always trying to clean grease, oil, dirt, rust, or mill scale off of something. I was aware of ultrasonic cleaners but because of bad reviews I have never gotten one. Most of them are generic and don't even have a company name on them. The complaints were all the same. Very slow to heat up, if at all, and didn't clean very well. They all look the same except for Vevor. They put their name proudly displayed. Almost all the reviews on the Vevor were positive so I ordered a 15 liter model.I also ordered some Simple Green Pro HD concentrate mostly because it is supposed to be friendly to aluminum while the regular is not. It also said it could be used in Ultasonic Cleaners. It arrived much sooner that what the projected delivery date given when I placed the order. It was packaged very well and there was no damage.I was in the process of fabricating a project using hot rolled steel flat bar and square tubing. Hot rolled steel needs to have the mill scale removed before it can be tig welded and powder coated. Grinding or blasting it off takes a lot of time and grinding discs are expensive. I gave up using that process when I learned that a good overnight soaking in white vinegar will loosen the mill scale and any rust but you then need to rinse the pieces off in water and a little scrubbing with a Scotch Bright pad. It's a little messy but it works very well. I had my parts soaking in vinegar when the ultrasonic clearer arrived. I was originally going to rinse and scrub them as usual but then I wondered if the cleaner would remove the left over residue so into the cleaner they went with 3 gallons of tap water and 3 cups of the Simple Green. I set the temperature at 55c and the timer at 30 minutes. It actually heated up pretty quickly and a placed an electronic thermometer in to see if it would actually heat up to the set temperature.After a few minutes it not only reached 55c and shut the heater off but it continued to heat to 57c which I verified on the thermometer. After 30 minutes it turned off and I pulled out the parts. I had a big smile on my face because the mill scale and rust were completely gone and the metal was spotless ready for welding after a quick rinse. I went from hours cleaning scale, rust, and oil from metal parts to doing nothing. Welded them up and another bath in the cleaner which removed everything from the welding and then powder coating which turned out flawless.Next up some greasy, oily 30 year old vise grips which I now use as a clamp for welding and grinding. There was so much build up of crud in the adjusting screw I could hardly turn it. Put a couple of other messy pliers in the cleaner also and set for 20 minutes. Times up, took them out they were all spotless and the adjuster on the vise grips turns like it did when they were new.I can't say anything about the unnamed brand of cleaners but the Vevor worked beyond any expectations I had. If you do metal fabrication and are tired of cleaning smaller parts before welding I highly recommend trying this clearer. You can pretty much put anything you want in as a cleaner. On You Tube I saw some guys even use gasoline. I won't be trying that. I also saw one guy who puts the white vinegar in the machine. I'm going to try that next to see if I can reduce an overnight soaking down to just putting the metal in the cleaner with vinegar.

Very attractive functional unit. All stainless steel with a lid and removeable power cord. Push button controls for temperature and time. I got the 15 liter model. Power for heating and cleaning are actually a lilttle higher than spec'd. Heats from 79F tap water to 100F in 23 minutes (can go as high as 176F). There is a ball valve for emptying and an included fitting and hose if you're not near the sink. I was cleaning a brass clock works that was pretty dirty and couldn't get to everything with a Q-tip, and didn't want to disassemble all the way down to individual gear level. I used an ammonia based cleaner concentrate, diluted 7:1. It got it VERY clean.Dimensions are important depending on what you have to clean. The tub is 12.75" x 11.75" x 5" deep to the fill line, or 6" to the brim. The parts basket is 10.5" x 9.5" Outer dimensions are 14" x 13" x 11" with recessed handles. It weighs about 19 lb. Still don't know where I'm going to store it.The only issue I had was the stated (15 liters) vs actual capacity. It actually measured 11 L to the fill line and 13 to the brim. Quite happy with it!

I purchased this Ultrasonic Cleaner (or should I say, *my hubby* purchased it) on the 17th of February of 2026. It came with what looked like a spherical tea-brewing wire-mesh basket, intended for holding small jewelry, but unbeknownst to either of us, it was also supposed to be shipped with a larger basket that could hold larger jewelry, such as bracelets, etc., which was not in the package. It arrived on the 20th of February, and all seemed well, other than the missing larger basket, a fact we weren't yet aware of.We did not use the cleaner every day, perhaps once a week, on jewelry that we regularly wore. It seemed to perform well, heating up to the target temperature that was displayed on the LED numerical display, and buzzing away, with the typical sound of an ultrasonic transducer getting to work, and using cavitation to clean our jewelry - until the 10th of April. On that day, something caught my attention; the water, despite being dialed in at an operating temperature of 55 Celsius (about 130 F), was cold. I power cycled the unit, and re-set the temperature to 60 Celsius, only to have the same thing happen; cold water. It was at this time that my husband and I discovered that the unit should have come with a lager basket, by checking the online documentation. Further reading revealed a fault; upon powering up the unit, the temperature readout displayed an error code "E1" for a few seconds, and then displayed the current water temperature. Once again, the unit would not heat up, though its transducer did buzz away at some fundamental frequency - odd, since harmonics go UP, not down.So, I called Amazon on 4/12, and was basically told; "..too bad. You're out of warranty and out of luck." I was incredulous, as I have never heard of Amazon telling a customer that they were on their own because they missed the warranty date by a few days - on not only a case of factory defect, but also on a case of a product being shipped with missing parts! I told the rep that I had no interest in chasing my tail over $40, and that they could keep their cheap electronics - I had better things to do.As of the writing of this review, my VEVOR 1.3L Professional Ultrasonic Industrial Cleaner with Digital Timer 40kHz Excellent Ultrasonic Cleaning Machine 110V for Jewelry Watch Ring Coin Diamond Eyeglasses Small Parts Cleaning machine has been relocated to its permanent storage location - the trash.This review is a factual recital of my experience with "VEVOR 1.3L Professional Ultrasonic Industrial Cleaner with Digital Timer 40kHz Excellent Ultrasonic Cleaning Machine 110V for Jewelry Watch Ring Coin Diamond Eyeglasses Small Parts Cleaning" machine. Respectfully, I can neither recommend this device, and in what is a first, I must also express my extreme dissatisfaction with Amazon's customer service. The fact that the unit was shipped missing parts is by itself a condition for action on Amazon's part, at least to the extent of contacting the manufacturer, and attempting to remedy that particular situation, in favor of the customer. To manifest abject apathy over a long time customer's situation, will hardly bring Bezo's house crashing down, but as is said in old proverbs; "ROME FELL".Peace!

We got the “VEVOR 15L Ultrasonic Cleaner with Digital Timer & Heater” as an alternative to paying a mechanic to fix/clean a throttle control body/carburetor for our ATV as it was cheaper. We chose the 15L knowing it would handle the size of our project plus larger items. Our ultrasonic cleaner arrived in good condition as it was well protected for shipping. It included a basket to place items in, a small basket to clean small items such as jewelry, a tube to connect to the unit for draining liquids and an instruction manual. We liked how easy it was to follow the instructions and use the ultrasonic cleaner. We are totally satisfied with the results of cleaning our carburetor/throttle control and its back to functioning as normal. This item not only saved us money in the long run, but we now have an item that can be used for numerous projects. We have no regrets at this point and can recommend it for cleaning your items.

This thing's got some power. The first thing I cleaned with it was the throttle body off my 2000 Jeep XJ. I've had the XJ for 26 years, and this is the first time I've cleaned the throttle body. Let's just say it was due. I used Dawn dishwashing liquid and Borax with hot water, and within a minute the water was very dark. I ran two 15 minute cycles and finished with a little light scrubbing with a soft bristled tooth brush. Great results.I have two complaints. It takes quite a while to heat up, so if you're using water make sure it's as hot as you can get it from the tap before you put it in the tank. The other complaint is the drain hose and the plastic barb. The hose is a bit on the thin side for the application, and when hot fluid hits it it gets very soft and tends to kink, and just not flow very well. But these are both minor annoyances. I fully intend to change the barb for a brass barb, along with a much stiffer hose.I really like the basket that comes with it. It's a good size for the kind of stuff I'm likely to clean. Dunno what to say about the small part ball that was included. I'm sure it will work fine with small items, as long as you're throwing them in with larger parts. The tanks pretty big for just small items alone. But I'm sure it would work.I'm not going to say it's loud, but you'll definitely notice it when it's turned on. I've got mine situated in my basement, and it's only really loud when you're close to it. Sitting twenty feet away in a different room it's not a problem.So, the upshot is this - it's well made, has lots of nice features, looks good and works great. Big thumbs up on this one.

The cats meow of parts cleaners. This 15 L model handles a large carburetor and saves you from scrapping a core because conventional cleaning just will not get into this small passageways where old gasoline will congeal into hardened varnish.When you turn it on it appears as though very little is happening (lot of buzzing, but no magical cleaning) but the concept is quite simple. The machine is producing billions of small bubbles that hit anything that is not metallic used it to crumble.A cleaning event MAY take more than one session of the unit is crusty but it WILL subdue the crud.If you have smaller parts (things that might fit into a Mason jar) you can fill the jar with a particular cleaner, drop the part into the jar and seal it and drop the jar into the cleaning solution. The high frequency bubbles are not deterred in the meat by the glass container and you don’t have to change out the water to use a special cleaner.I’ve had a small version to clean my glasses sitting on the bathroom counter and the small crevices of the wire frames NEVER accumulate any crud.Darrow...for the Prosecution

Uso Odontologico:Si lo quieres usar para tu consultorio viene bien, caben perfectamente los fórceps abiertos , yo meto todo el material de la foto y hasta cabe màs.Lo he usado por primera vez y me ha encantado, la verdad si quita toda la suciedad que puede llegar a quedar muy retenida en el instrumental, como en las bisagras de las pinzas o perforadora de dique, no le pongo 5 estrellas porque la manguera llegó con detalles , me imagino que no tiene nada que ver en el funcionamiento y también por el acabado del pegamento que se logra apreciar en el video, fuera de eso, esta excelente.Habrá que probar unos meses más el funcionamiento y actualizare la opinión.

Buen producto por el precio, lo volvería a comprar

Buenisimo para limpiar joyería y excelente para limpiar cadenas de bicicleta. Lo uso con jabón biodegradable en dilución y a altas temperaturas y funciona perfecto. Deja manchas de agua si tienes mala calidad de agua pero tienes que limpiar inmediatamente después de uso para prolongar su funcionamiento. Que puedas regular temperatura y tiempo la hace la mejor

La caja venía dañada, el producto se ve como si estuviera usado, incluso traía restos de agua, su funcionamiento cumple pero no es el mejor, por el precio hay mejores opciones. 3 días seguidos me marcaba que llega el producto y no era así, se entregó tarde

Todo bien, buen producto, solo que a mi gusto un poco grande, pero bien