FNIRSILCR-P1 Transistor Tester, Mosfet Transistor Capacitor Tester, SMD Electronic Component Tester, Diode Triode Zener Diode Resistance Inductance Battery Test LCR Meter MOS PNP NPN ESR Meter

Besides identifying the characteristics of transistors, diodes, zener diodes, etc., this device will give ballpark readings of R, L, and C. Not as accurate as my LCR meter but often it's good enough.

Very cool little tester fir the price. Dies have a little anomaly with bipolar transistors. Sometimes it identifies them as an f.e.t. When they are not. But seems to work pretty well.

This tester works very well. Type C charging. It has an accessory to facilitate testing SMD devices.

I received it less than 24 hours after ordering. That’s amazing. After charging the battery, I gave it a shot. After every attempt to measure, I got the “component missing or unknown” message. So it’d take the part out, clean the leads, and put back in. Then it would usually work. I’ve since discovered that it *always* gives that error message the first time you push the Test button. Ignore it, push it again, and it will work the second time.I previously had one of those earlier versions that cost about half as much and is without an enclosure and uses a 9V battery, but it conked out. Anyway, I think it was more accurate and had a faster response time than this one. This one is pretty accurate with resistance (maybe 1%), but maybe not as good as the older model with capacitance and inductance. Capacitors measure about 7% off or more. Not terrible but maybe could be better. Inductor measurements are similar with 10% or more error. It’s hard to judge the accuracy of BJT, JFET, MOSFET, but those checks appear OK. One good thing - I was surprised at the published high end of the range for C and L, and I verified it will measure ten times or more what’s specified.

If you don't read the instructions like I didn't you got to hook up the clippy leads to the diode and then hook it up backwards to get the voltage drop or whatever to find out what the voltage is of the zener diode

This product is disappointing. I have given it some time before writing this in hopes that the manufacturer will provide firmware that enables this to function properly, but firmware 1.0.8 still has serious flaws. Most annoyingly, for NPN transistors, you will get complete different leg identifications depending on the which legs are seated in slots 1/2/3. Pin/leg sequences should be consistent across all seatings, but I see C and E are frequently swapped. Apparently QC is minimal with this company.It looks nice, but the IR feature is almost useless except for verifying that a signal exists, the tester is slow, and it has serious deficiencies when used for transistors. I wish I could return mine.

This tester not too good if you test Transistor and won't look at Transistor spec then you may think it works beautiful but some Transistors are ok, don't get me wrong but some of them are not, it gave me wrong PIN configuration that mean I cannot rely on this device, whenever I cannot find a spec for Transistor then I am doom cannot verify a correct PINI tested Transistor 2N3904 and it gave me PIN-E(3) and PIN-C(1) but the spec said PIN-E(1) not (3) then PIN-C(3) not (1) no matter which way I insert Transistor forward/backward still gave me the same.then I tested another Transistor BD139 and it gave me PIN-E(2) instead of (3) and PIN-C(1) instead of (2) and PIN-B(3) instead of (1) completely wrong, but when I try to turn Transistor facing opposite direction inserted and test it, came out correct as a spec. So what is in the world do we know which way we suppose to insert Transistor into this device? First I seem to like it a lot but my trusting on this device is down due to incorrect results.Oh by the way I also try update firmware from version 1.0.4 all the way 1.0.7 each version is the same resultI want to post it here so people can see or maybe have an idea to fix it?

I tested a variety of individual components in my parts bin. This works as advertised. A very low value inductor was identified as a resistor, but then correctly measured. A larger inductor and a speaker were correctly identified as inductors, reporting impedance and inductors. Transistors were correctly identified. Connect devices to any of the numbered pins, which pins has what polarity or function will be identified.When pressing "Test" to power up, you will need to press it again to test the device. I missed this fact and thought the thing was broken. 3 test leads and two fixtures are provided to assist in connecting. I don't know how this will perform for devices in a circuit. That also depends on the circuit. It has a shorting relay for capacitors but I suggest shorting them before testing.One problem with more expensive testers is that any testing device can be misused and damaged. This one features "Less tears", a very low replacement cost. For a beginner with limited knowledge, that's an important feature.