Sovol Filament Dryer, SH02 Dry Box Filament Sealed Storage Box 3D Printer Spool Holder with PTC Heater, Filament Dehydrator with Touch Screen, One Key Set, Compatible with PLA PETG TPU ABS 1.75/2.85mm

Working great so far, simple to use, noise level is not an issue and print quality has improved. I've placed it next to my Elegoo Centauri Carbon and directly feed into the filament sensor using the supplied PTFE tubes instead of using the roll holder. Helps to have the door slightly open to vent the humidity during drying. Added 2 x desicant bags that came with the Elegoo filaments into the trays inside the chamber as they are the perfect size.

Really good PETG no problems, no stringing, prints come out perfect every time and highly recommend. I printed most of the AT-AT walker using the gray PETG: Legs, feet, neck, under walker and inside the walker.

Excellent Screen with all details on display.Very easy to change settings. Downside VERY NOISY. The ease of changing the settings might make me buy again despite the loud noise.

I’ve not had these long but they seem to work perfectly. The touch action is responsive and easy to use. It maintains temperature well. Those that say it increases humidity need to understand humidity. It even says in the instructions to open the chamber a few times to allow the moisture to escape. When you do the humidity plummets and eventually stabilises. I don’t like the outlet option. I drilled two holes in the back so I can feed directly into my U1.

Prints well, lovely shine on finished product.

Works as intended and filament rolls out nicely. Although the point of exit could be moved slightly to ease friction i have not had problems.

This dryer feels better quality compared to others in this price category. But it has one flaw - HIGH PITCH NOISE fan. It's so annoying that i'm not sure i'm going to keep it. Other than that, body plastics, layout, lid with gasket, touchscreen - everything feels much better than competitors, space-pi for example. The annoying noise is a huge flaw. I'd happily pay £10-15 more for a quiet fan...

Works well, has a fan and exhaust hole which is a nice feature my previous one didn't. Only slight downside is that my ASA filament has a recomended temperture of 80C for drying and this only goes up to 70C.

Después de varios meses usando el producto la verdad que va muy bien, al principio no pensaba que fuera a hacer mucho en los filamentos con humedad pero la verdad que dejando el filamento secando durante unas cuantas horas las impresiones salen como si el filamento fuera nuevo, nada de hilos molestos, me gusta que tenga varios perfiles como PLA TPU PETG etc... El precio está bien, hay productos muy parecidos pero me decanté por este por el precio y por poder secar 2 bobinas de filamento a la vez.

Funziona perfettamente, ottimo acquisto. Essiccatore con capacità’ di due bobine con filamenti pre impostati

I bought the Sovol filament dryer after spending months blaming my printer for problems that were very clearly caused by me storing filament like decorative pasta. At first I thought, "How much difference can dry filament really make?" The answer was uncomfortable. The first roll of PETG I dried produced noticeably cleaner prints, less stringing, and fewer mysterious defects. Apparently filament prefers not to absorb half the atmosphere before being melted. The best feature is being able to print directly from the dryer. Instead of drying filament, taking it out, and immediately exposing it back to the air like some sort of moisture reintroduction programme, the filament stays protected while printing. My favourite moment was hearing PETG print without the occasional crackling and popping noises that I'd previously convinced myself were completely normal. They were not. The dryer is simple to use, heats reliably, and has quickly become part of my standard printing routine. New roll? Dryer. Old roll? Dryer. Roll that's only been open for six minutes? Surprisingly, also dryer. I've become the sort of person who talks about filament humidity levels as though I'm managing a wine cellar. "This PETG has been properly conditioned." "The TPU needs a few hours in the dryer." The printer doesn't care, but I certainly do. The only downside is that it reveals the truth. When a print fails now, I can no longer immediately blame wet filament. Sometimes the problem is my slicer settings, my design, or my decision to start a 14-hour print and walk away. Highly recommended. If you print with PETG, TPU, ABS, or pretty much anything that enjoys absorbing moisture, this thing is worth having. Five stars. My filament is dry, my prints are cleaner, and I've added "filament moisture management" to the growing list of hobbies I never expected to have.

Mi problema es con Sovol directamente, compramos primero directamente con ellos y nunca pudieron resolver, nos cobraron el envío de la impresora junto con la secadora y nunca llegó la secadora, cuando reclamamos, nos querían cobrar de nuevo el envío y sin más ni más no nos resolvieron y solo regresaron el dinero, pero sin lo que habíamos ya pagado de envío, dijeron que ya se había usado en la impresora

結論から言えば、どのフィラメントドライヤーを買うか迷うならこれを買えばいいです。 真空パックや防湿庫など湿気自体を取り込ませない対処法もありますが、やはりそれでは限界があり最後には吸った湿気を吐き出させる道具(=ドライヤー)が必要になります。 このジャンルは他にも競合製品は多数ありますが、個人的には以下のような理由でこの商品を選びました。 ・簡易的な保管ケースも兼ねる ケースにパッキンがあり、バックルで蓋を固定できる=ケース自体がある程度の密閉を保てる構造になっています。 ケース底に乾燥剤を入れておくスペースがある事からも設計者はこのケースにフィラメントを保管する運用を想定しているようです。 ついでにいうとバックルで固定するので蓋を持って運んでも問題なし(バックルに負担がかかるので避けた方が良いとは思いますが) よくわかっとるデザインです。 ・必要な機能はあり、その割にコンパクト ファンによる空気の循環、ケース底の乾燥剤入れなど欲しい機能は一通りあります。 それでいてデザインは丸く、無駄に突き出したりしていないので、体積的にはフィラメント2本とそこまで差がないくらいにコンパクト。 ・ユーザーが多く、問題点は全て解決可能 最大の理由です。よく売れているから良い物”とは限らない”のですが、よく売れている分だけ”ユーザーの知見が蓄積しより良くなる”というのはあるでしょう。 この商品に関してはその点が極めて大きく、欠点自体はあるにせよそれを解決するための方法(プリントできるパーツ)は調べればほぼ出てきます。 ついでにひとつ: 空気穴が小さすぎて乾燥中の湿気が抜けきらない点に関してはバックルを蓋の間に挟めばちょうど良い隙間ができます。もしこれが意図した設計なら、このような応用を出来るようにするデザインは神技のそれです。 ・安い これだけ揃ってこの値段、しかも2本保管できます。競合製品より安い。 金額不問ならともかく、コスパを求めて買うのであればこの商品を上回る物は現状存在しないと思います。 (同価格帯の他の商品にはこの商品より性能が劣る or 自力でパーツをデザインしない限り解決できない課題があるので)