Eco-Fused Adhesive Copper Foil Tape - Double-Sided Conductive -2 inch (50 mm) - EMI and RF Shielding, Paper Circuits, Electrical Repairs, Grounding, Arts and Crafts, Home Interior (2 inch (50 mm))

Used this tape for a craft project it works very well. An added bonus my dog loved it! Something about it one of the dogs found irresistible. We have other tape around the house they ignore. This one we have to keep in a cabinet up high out of reach, the trouble is it’s pretty sticky so makes it time consuming to get it cleaned up off of him.

I service dozens of laptops every year and have been searching for a good double-sided tape with multiple uses that include reattaching the rubber feet on the bottom of the case. I've probably tried half a dozen different products with less than stellar results. Until now. This product is different than any other tape I've seen. It's like a paper thin layer of gel adhesive and appears very similar in consistency to the original adhesive used on laptop feet. While it may appear difficult to use on first impression, I did discover a relatively painless way to apply to the rubber feet. I first cut off a small piece of tape slightly larger than the feet. Laying it down with the sticky side up, I pressed the feet down on to the sticky surface and applied pressure for about 15-20 seconds. Moving the strip of tape with feet now attached to a piece of cardboard, I used a hobby knife to carefully trim around each foot, trying to cut just the tape layer and not the backing. That was probably the trickiest part as the tape tended to bunch up a bit as I was trimming it. Nevertheless, once I had the tape on each foot trimmed, it was fairly easy to pull the foot with its circle of tape off the backing and attach it to the bottom of the laptop. Again, I maintained pressure for about 15-20 seconds and had a good, secure bond that appears to duplicate the characteristics of the original adhesive - holding well, but removable without damage if needed. This is the tape I've been looking for.

Used this tape to adhere to a 3D printed item made of PLA. There was no issues with it sticking to the plastic. I did run into it moving once soldering onto the tape but that is attributed to the heat loosening the hold that the adhesive had, this is to be expected. There was absolutely zero issues with soldering onto the tape, the main reason why I purchased this tape as aluminum tape was impossible for me to solder onto. This tape's length was far too much for what I needed for this project so I will have to find uses for it elsewhere and by the looks of it, it wont be hard to find things for this tape. I used this tape to create a commutator for an electro-magnetic motor. The solderings was for attaching the windings to the commutator. I used a utility blade to cut the copper tape for segmentation of the commutator, the act of cutting through the tape was effortless and separating the copper tape was also without an issue, thus allowing proper isolation of the windings and a perfect conductive "tooth" for electric current to pass through. I'll be sure to add a photo once I've fully assembled the motor. I would highly recommend this copper foil tape for any electronics enthusiast.

Tape works well, and it does what it does. However if you need to cut it or make small strips it is hard since it comes off/slides off the tape backing. Soldering on it is easy and works like a charm. Easiest way to use and make the most of this is to apply first, Then make your cuts using xacto knife or small scraper.

Using this to make sticker for my planner and junk journal.

This is simple. It works. It's sticky enough. The adhesive is conductive enough that I measured less than an Ohm resistance across the guitar I was shielding through multiple layers of adhesive. To connect different sections it was possible simply tape down the bare wire on each side instead of soldering.

I bought several rolls of this copper tape to use for a crafting project for a garden club. The copper tape worked perfectly. Easy to use, and stuck well onto glass tiles. Perfect for our application. And, very reasonably priced.

I needed a solution for attaching my bass drum hoop saver back to the hoop. I have tried a couple others solutions and they were either so so or not working the way I wanted. This double side adhesive tape is strong yet removable if you really want it. Awesome product and I have already started using this to fix other things.

This stuff is thin. REALLY thin. So thin that it's as if it isn't between the two items stuck together, except that they really do get STUCK together very well. Strong adhesion, no geometric distortion because of how extremely thin the tape is. Wonderful product! I use it for all kinds of purposes in the woodshop, mainly when a temporary bond is needed. Eg. attaching temporary stops, guides, or fences to the machinery. Or for bonding a stack of identical parts together so they can be mass-machined as a unit to exactly the same dimensions. Etc. Just be wary that it is very strong stuff, and getting them apart again afterwards can be tricky. So don't overdo it with the tape! I already bought more, and likely will again as my on-hand supply depletes. HIGHLY recommended!

Very easy to apply and adheres will. I purchased this to ward off slugs from my strawberries. I stuck a ring of this taped around my planter and it not only stuck really well but looks quite good cosmetically.

銅とアルミを組み合わせることで、鍼灸の電位療法を起こすことができ、生体電気を整えることができます。

Fa quello per cui è stato progettato. L'ho preso per ritagliare dei rettangoli da usare con le foto tessera e mi trovo molto bene.

Dun en plakt prima. Alweer de derde rol. Nog steeds tevreden.