BT7 Touch RV Backup Camera Wireless 7" Touch Screen Monitor System

I’ve installed several cameras on two different RVs over the years, always searching for the best image quality—especially at night. After trying many options, I can honestly say this camera delivers the best image I’ve ever seen, even in low-light conditions. The clarity during the day is excellent, and the night performance is outstanding. The connection is also very strong and stable, which is extremely important for RV use. Installation was straightforward, and the reliability has been great so far. After a long search and multiple camera setups on my RVs, I’m very pleased with this purchase. My search for the perfect RV camera has finally ended.

Perfect Solution! Crystal clear picture, works like a champ. Easy to install and synch with the console display.

Must have on your RV. I installed the Haloview BT7 Backup Camera and the BTC129 RV Side Marker Cameras. I also installed an additional camera on the top Left front of my camper just above the running light (this camera paid for itself not only as a security camera but when I was caught in a traffic jam behind a Semi, I could see around the big truck.) . The 7" Haloview screen gave me excellent and clear vision from all the cameras. The backup camera was the most impressive with a clear field of vision of the rear of the RV, left to right and AFT. I was able to see vehicles behind me clearly which allowed me to change lanes without guessing if I had enough room to change lanes. The BTC 129 side cameras paid for themselves when I was trying to pull away from the gas pumps. The problem that I faced was not being able to see how much room I had between my camper and the gas pump island when my truck was turning out of the gas station. I simply turned on the side camera and I could see how much room I have. I built a RV security system with my Haloview system. I bought a connector outlet and wired the camper so I was able to plug into the camper battery. I placed a switch inside the camper so I was able to turn on the camper lights/cameras from inside the camper. I almost have a 360 degree view around my camper. I have a security camera view is from the safety and comfort inside my camper. The total upgrade was well worth it money and the effort.

After doing hours of research and reading/watching YouTube videos I selected Haloview over Furrion. I’m very pleased that I went with Haloview. The functionality, screen clarity and brightness is a thousand times better than the Furrion. My Jayco travel trailer came setup for Furrion so there was a dedicated power line for the camera already there. Haloview came with a Furrion power adapter so no splicing was necessary. I removed the four screws from the Furrion camera bracket which you have to remove as well. I will note the I reused the screws as they were black and matched the Haloview bracket/camera much better than the supplied stainless steel screws. The installation was very easy, it took more time prepping the area than the actual camera install. The camera and monitor were already paired at the factory but I checked just to confirm. If you’re on the fence about which camera to choose as I was go with Haloview and you will not be disappointed. Also, did I mention that you can record with the Haloview you just have to purchase a memory card.

Very good back up camera. I have had three others over the years. This one is very clear and hasn't lost reception on my 32 ft 5th wheel.

Great video quality and overall it works well. The picture is clear, the system is easy to use, and it does what it’s supposed to do. The only downside I’ve noticed is some lag in areas with poor phone reception, though I’m not completely sure if the two are related. Other than that, it’s been a solid backup camera system.

I replaced a Voyager WiSight 2.0 camera and monitor (on an Airstream trailer) with this package. When replacing the camera it wasn't easy to access the existing wiring in the wall, so I just cut both leads and used these connectors: https://www.amazon.com/dp/B071R2J7JP (waterproof and no stripping) to splice the BTC128 camera onto the power wires. I also used my own stainless #8x1/2" screws since I wasn't sure the screws that came with the camera were stainless (they didn't exactly ignore a magnet). I haven't had a chance to tow the trailer with it yet, but it's clear the resolution is better (for Voyager owners with pre WiSight 2.0 cameras it will be a lot better). I'm a little concerned though, that the field of view may not show as much of the area immediately behind the trailer (with the camera aimed as low as it would go) as I had with the Voyager. Will try to remember to update after a few tows. Characteristics of the BT7 monitor that could be better: 1) It doesn't remember the last on/off state, and also doesn't have a setting to control the default startup on/off state. I don't remove the monitor when not towing, and would rather not have the display on and constantly telling me "no signal" when I'm not towing. 2) If trying to windshield mount the monitor close to the roof (to not block your field of view above the dash) the antenna mounts on top and antennas that waste a good inch of length before the folding joint -- don't exactly make it easy. It would have been better if the antenna connections were located on the sides (near the top) so the antennas could simply be folded down (vertically) and not occupy any space (period) between the top of the monitor and the roof. As something of a work-around I picked up some SMA adapters (https://www.amazon.com/dp/B0CJJ7BM7C) that have some short right-angle connectors and allow the monitor to be mounted much closer to the roof line. Overall, the BT7 monitor seems well built (a bit better than the Voyager monitor it replaces). The reception seems as good or better than the Voyager. The BT7 does have the "dash cam" recording capability (which the Voyager didn't have), and the windshield mount seems to have a much better grip on the glass than Voyager's did. Also, being able to pair and easily switch to a 2nd (or 3rd, or 4th) camera adds considerable value (e.g. the battery powered BTC126 with magnet mounts).

Two complaints and a whole lot of praise. Wires. Gauge of + - Gnd elements are thin, LED light thin. Insulation was thick. Wire gauge was mismatched with guage of Tvl Trailer and my crimp connector was all gummed up. I switched to the white crimp connector they provided on the side cameras, similar gauge mismatch. Their connector worked better. Also lead on rear cameras was too long and not long enough, depending on how one approaches the install. Owner/install manual, is mostly quick install pictures. And not very descriptive ones. doesn’t matter though, i found the equipment very intuitive and it came together with the main and two side cameras very well. The Pairing cables are useful, I don’t think there is data exchange, but sitting at my camper table and connecting rear and two sides cameras worked will to help me figure out the system with the spare manual. I liked the cigarette lighter power button. During install. I took a little too long figuring wiring out with the first side camera, the second side went on in 15 minutes, all paired up. Side camera has two sets of wires, one for the camera and one for the lights. I will run separate power to the camera later to use the system when in the trailer. The display is FANTASIC. The improvement in performance over my 5yo furion is remarkable. It is a huge value for the money. Can’t wait to add TPMS and axel heat sensor, the usable field of view is very good and benefits from camera fidelity.