CURT 13386 Class 3 Trailer Hitch, 2-Inch Receiver, Select Ford Explorer, Police Interceptor Utility,Black

So far I've only pulled Jet Ski's and dirt bikes so I'm nowhere near the weight limits, but I don't intend to pull anything too close to them with an Explorer anyways. It's super solid though and I wouldn't be afraid to load it down with a heavier trailer if I need to someday. Install was actually very straightforward. The bare minimum extra tools I would recommend is a decent torque wrench to get the new bolts torqued to the correct spec. An electric or air impact wrench will make getting the old bolts off super easy, but if you don't do much work otherwise that's an expensive tool to sit around. An exhaust hangar tool will make short work of the hangars, but I managed without one and just a bit of good old elbow grease. Maybe rent one from autozone for a day but I wouldn't buy one unless you plan to mess with your exhaust more than once. Also, of course a second person to help lift the hitch up to the frame is incredibly helpful, I'm sure you can manage it alone if needed too. What I expected to be the most difficult part was fishing the extra bolt and metal plate up into the frame turned out to be incredibly easy with the included "fishing tool" thing that was included, I just left it threaded onto the bolt until we had the other 4 bolts holding the hitch onto the frame incase we knocked it out of place, but it was no issue. Overall installing the hitch itself was super easy and nothing actually stopped us from installing it. Took about an hour total because I work slow and extra careful. I sawone review that claimed the foot kick sensor for the rear hatch no longer worked, and I was very worried about this since my wife quite likes that, this is untrue though (unless you somehow disconnect or break your sensors). You just have to kick to either side of the hitch now. The sensors obviously cannot see through the hitch itself but they're wide enough that they can see off to the sides of it.

Direct bolt on. Perfect fit

Everybody says "easy to install - 40 mins" -- which I don't disagree with, but the instructions (even as clear as they were) had 2 things confuse me. The muffler hanger bracket (not just the rubber part, but the metal piece bolted to the car) - wasn't clearly described as needing to be removed. Obviously it comes down and gets tossed, those are the same holes the hitch will bolt in to. I have no clue what the "other" bolt you have to fish through hole is for - I installed it correctly, but not clear why -- unless it's meant to be a grounding source for the light kit? My other beef is the torque specs seem off to me - and it would make a heck of a lot more sense to torque the bolt attaching the rubber hanger before you try to install and bolt the hitch under the car. I learned this after following the steps - thinking I could easily get in there. I also found the forward bolt difficult to get to with the mufflers hanging down, I still needed more side to side clearance to get after those bolts. Perhaps if I dropped the 3rd muffler bracket where the 2 pipes join further up the chassis - I would have a lot more play in the whole assembly. I was cautious though, not wanting to break a weld further up by putting too much pressure on the exhaust system. Other than me stepping on myself in a few places, it's easy enough to install - I'm sure future installs will go in 30 mins easily.

great product, well made, arrived just on time.

The installation process is rapid and straightforward, making it suitable for users of all skill levels. The instructions are clear and easy to follow, ensuring that anyone can complete the setup with minimal effort.

Installed on 2012 Ford explorer. Hitch fits as designed without any need for cutting or drilling. Hardware was sufficient. Install would have been fairly easy if instructions included an additional note which is very important for the ford explorer install. IMPORTANT!!! The step where the carriage bolt and flat metal plate are inserted into the body of the vehicle should include a note saying to insert the bolt, followed by flat plate and explain to insert the flat plate by the longer side of the plate into the hole first. Inserting the shorter end first prevents the plate from laying in place flatly inside the vehicle frame because the end of the body channel it is inserted into is capped off and prevents it from centering over the hole. IT MUST FACE THE OTHER DIRECTION. The pictorial parts breakdown does show the correct direction, but the written instructions don't say anything about which way it must go. It is an absolute nightmare to get the assembly back out once it's put in wrong. Please take my advice and pay particular attention to inserting that piece in the right direction and get it the correct direction the first time. All else was good except delay in shipping which could have been fault of carrier or seller. I won't speculate either way but will say it did not arrive the day it was supposed to.

Hides away quite nicely for a non-factory hitch.

Es un poco pesado para la instalacion, pero es muy solido y encaja perfectamente en los orificios. Contiene todo para la instalacion, Excelente calidad y acabado. Super recomendable

La entrega fue a tiempo… pero la forma de entregar fue muy mala, el artículo no viene empacado o por lo menos protegido, de hecho el artículo llegó raspado como se observa en la imagen… la marca es reconocida y creo que demerita completamente la manera en la que se entregó…

Fits perfectly on 2019 Ford Explorer

Instalation super facile. Plug and play