1/8" Baltic Birch Plywood for Laser Cutting and Engraving, Pack of 20 | 3mmx30cmx30cm, Higher Density And Rigidity Than Basswood, Top Pick For Sturdy, Load-Bearing And Long-Lasting Projects

I use these on both my xtool lasers (F1 Ultra & M1 Ultra). Good quality wood for the price. I've made many layered projects with these. I use my scroll saw to cut usable pieces off. Those smaller pieces of wood I'll make earrings with.

Love this wood, cuts great on my laser machine.

Product is as describe.

I agree with others that say that the panels have bad spots where your laser will either not go through at all or have a really hard time when laser cutting. I'd say I had bad spots on about half of my sheets. I usually cut out pieces of layered ornaments on here and am able to cutout about 9 per sheet. Of those 9, maybe only 1 or 2 don't cut through all the way in some small areas. I usually just score the back with a knife afterwards so that I can push it out, but it usually ends up in a not-so-clean cut in those areas. Overall, I would still probably come back if I needed these in a pinch, but I would likely jump to the first option I can find that is cheaper since these didn't blow me away.

The price was good on this plywood, but I cannot recommend it. I would not purchase again. If you place any value on your time, it is not worth it. It is the lowest quality wood I have purchased for my laser. Here is why I would rate this wood at 1 star. 1. The plywood was advertised as 1/8" thick, but the wood I received was undersized. 2. Many of the sheets have defects running the entire length, some poorly patched, some parts not even patched. 3. There are a lot of glue filled voids and even using very generous speed and power settings, I had to do a bunch of exacto knife cutting on the back to free the parts and then you still have a bunch of char on the cut. If you are doing multilayer or mandala, this will be a huge hassle. I've hit bad spots on every piece so far. 4. The wood is fairly warped, although some warping is expected on ply this thin. 5. Each piece of wood is individually wrapped. Why? 6. A few pieces had broken corners. The price was good on this plywood, but I cannot recommend it. I would not purchase again. If you place any value on your time, it is not worth it. It is the lowest quality wood I have purchased for my laser. Here is why I would rate this wood at 1 star. 1. The plywood was advertised as 1/8" thick, but the wood I received was undersized. 2. Many of the sheets have defects running the entire length, some poorly patched, some parts not even patched. 3. There are a lot of glue filled voids and even using very generous speed and power settings, I had to do a bunch of exacto knife cutting on the back to free the parts and then you still have a bunch of char on the cut. If you are doing multilayer or mandala, this will be a huge hassle. I've hit bad spots on every piece so far. 4. The wood is fairly warped, although some warping is expected on ply this thin. 5. Each piece of wood is individually wrapped. Why? 6. A few pieces had broken corners. UPDATE: This ply also chars badly. Look at the picture I uploaded that compares it to a higher quality wood. I made both these cuts at the same settings, one after the other. This not from glue filled voids, every inch of cut material is charred and it's a huge mess to clean up. I will probably toss this stuff as it's just not worth the time to try and clean it up for acceptable results.

Cut nicely would buy again

I ordered the 8-pack of "3MM(±5%) thickness, each measuring 12x12 inches". I knew from the photos that they were really 300mm on a side, which is just under 12" and I'm OK with that. But the "3MM(±5%) thickness" and the image showing a caliper measurement of 2.96mm is TOTALLY wrong. Yes, they are very nice boards as far as surface finish goes. Six of them are perfectly clear on both sides, one has a minor black blemish on one side, and one has some dark areas and splits in the top veneer. See photos. Also, each board is individually wrapped in plastic to keep them clean until used, which is a nice touch and appreciated. My complaint is the thickness. They are advertised as 3MM ±5%, which would be 2.85 to 3.15mm. As received there is a label on the bundle that says they are "2.7 - 3mm", so right there you know you're getting short-changed on thickness. But wait...there's more! The stack of 8 boards, including the plastic film on each board, measured 22.32mm, which means the average thickness is 2.79mm, again, less than the advertised thickness. After removing the film, the actual board measures 2.60mm thick, not even meeting the labeled minimum thickness and far from the 2.85 minimum that was claimed when I purchased them. I will find a use for them because the surface finish is so nice. But even at 3mm I wasn't sure they would be thick enough for my project, and now that I find they are over 13% thinner, I'll have to look for another supplier.

As someone who relies heavily on laser cutting for both hobby and professional projects, I’ve tested a variety of woods—and this Birch consistently stands out. This particular batch exceeded expectations in both consistency and performance.

Perfect for hobby crafts.Strong Great price for 8 sheets Well packaged