XiKe 4036ER2004A Front Load Washer Tub Bearing ＆ Seal Kit | Fits 4036ER4001B, 4280FR4048E and 4280FR4048L Rotate Quiet and Durable, Replacement for LG and Kenmore Etc.

This kit UPC X001KGU29X has been installed for about 2 weeks. As of now works great. The washer is quiet again just like new. Well work spending $600 - $1500 on a new washer. FYI- the kit is NOT made in USA. The one I received was made in China. The side plates that hold the grease in the bearings on one of the bearings seem to be made of a plastic (probably Delrin type material, not stainless like the OEM). That's probably fine since its just to keep the prepacked grease at the ball bearings. My mechanical disposition: I am not a mechanic, I like to DIY to save money, reduce waste, learn about how things work. I would rate changing the "bearings" on a Washer to be "Medium dificulity". What I define as Medium difficult DIY tasks are: changing toilet overflow fill valve, replacing sump pump, changing or reparing a faucet, changing oil or brake pads on a car, basic circuit diagnostics. Explain why I indicate good fit instead of exact fit. New bearing measurements were approximately .02 inch off compared to original bearings. From a tolerance perspective it probably is fine. As others have indicated, the DIY repair is very straight forward, there are plenty of YouTube videos. Take pictures of what you are taking apart so that you can see for reference when you put it back together. If it is your first time taking apart our drum assembly, count on 6 hr to be safe. Make sure you replace both seals and clean out where they sit. Don't try to save time by not doing it, if it leaks afterwards you will have to take it apart again. The hardest part of the job is getting the old bearings out. Take your time and back them out evenly. Use the old bearing later to push the new bearing back in (this will protect the new bearing, since you will be impacting the old bearing to set the new bearing in place). I will update this as time goes on on the durability and reliability. Long Term update 9/17/2022 The washer started making loud noise during the spin cycle again. So from a durability perspective only lasted 2 years. These bearings have a 5 year warranty. I will reach out to the manufacturer for replacement. I was very careful about the seal replacement. Will add details to the condition of the seal when i take it apart. Talked to the seller, they refunded my purchase cost of the kit. What failed: After taking apart the washer this is what I found. The failure was in the seal. The seal failed which resulted in water getting into the bearings. Eventually that caused the failure of the bearings. If the seal had not fail, I am sure the bearing would still be fine. I can see that the seal failure was attributed to the reinforced silicone O ring that supplies tension on the spider shaft. This tension keeps water from getting past the seal into the bearings.

First and foremost, installing these bearings is not a quick or an easy task. It was hard work with unforeseen issues. In the end it was worth the effort because the washer is now operating like new. And now the review. I'm writing this review about two months after installation. This bearing/seal/o ring kit worked perfectly. I'm extremely happy with the purchase. But the install process wasn't easy. This is not the fault of the bearings. It was due to the age and condition of the washer. And the method I used to remove one of the bearings that was galled onto the drive shaft. And now some background on the repair. This may help you decide whether to attempt this repair yourself. My LG WM2301HW washer is 10+ years old. I've had to perform several repairs on it over the years including: - replacing the drain pump. - replacing the shock dampeners. - replacing the rotor (part of the direct drive motor). So I'm not afraid of taking the washer apart. It's a well designed machine that isn't difficult to repair if you have tools, mechanical knowledge and you watch a few youtube videos. This washer repair was the most complex one I've performed so far. Over the past few years the washer has started "walking" when on the spin cycle. I replaced the shock dampeners but that didn't completely solve the problem. Over the past six months the washer has started howling during the spin cycles. Anyone with familiarity with machines would recognize that sound as bad bearings. And the sound was getting worse. I had to either fix or replace the washer. I investigated having the washer repaired professionally but was told by two repair services that it wasn't worth the cost. So I decided to repair it myself. I went into this repair with the mind set that the washer was toast and it had to be replaced. $30 for the bearings was a risk I was willing to take. I watched a few youtube videos and got started. It should be noted that the videos weren't all the same. They did things in different orders and in different ways. For example one video removed the drain hose completely from the bottom of the drum and another just disconnected one side. To complete this repair the drum has to be removed from the washer. Disassembling the washer to free up the drum was straight forward and went well. No issues. Removing the drum was difficult. It's heavy and awkward to handle. I needed a helper to lift it out and put it back. With the drum out I could take it apart and remove the stainless steel basket. The basket is the thing that rotates with your clothes. This is where things got very difficult for me. The basket has a drive shaft on one end that goes through the seal and bearings then connects to the rotor of the motor. The shaft is supposed to slide out of the bearings and the bearings should stay in the drum. This didn't happen for me. For me, the large bearing was galled onto the drive shaft by corrosion caused by water that passed by the deteriorated seal. I tried everything to remove the bearing including Kroil, a blow torch, hammers and prying. It wouldn't move. In desperation I borrowed a seven ton gear puller from O'Rielly's auto parts. This is what finally got the old bearing off. I needed a long breaker bar to tighten the puller. I had to wear protective equipment because I was afraid something was going to shatter. With everything I tried, removing the bearing took a few days of after work activity. Once the bearing was off, I cleaned the drive shaft with emery cloth to remove corrosion and then cleaned the housings in the drum that receive the new bearings. I put the bearings into my freezer overnight before installing them into the drum. This shrinks the bearings and makes them easier to install. From there it should have been a simple matter to put everything back together. And it was until it was time to install the rotor into the drive shaft. This step is right near the end of the reassembly process. There's a spline where the shaft plugs into the rotor but now it didn't fit. What I discovered was that the massive force from the puller had mushroomed the spline to the point that it was too wide to fit into the rotor. This is when depression set in. And it's when I got out my files and started working on the rotor and the shaft. Working slowly I removed enough material from both sides that I was able to get a press fit of the shaft into the rotor by using the rotor attachment bolt to force them together. From there I was able to complete the install. Overall the repair took a week to complete working nights after work. Three of those five days were spent on bearing and spline issues. And all that time my family was complaining that they couldn't wash their laundry. When I pointed them to a nearby laundromat, they decided to wait for me to complete the work. Now that the work is complete I can honestly say that the washer is as good as new. It's quiet and as a plus, the washer doesn't "walk" around anymore. The worn bearings must have allowed the basket to vibrate enough to make the washer walk. Would I do this repair again, yes. But I'd wait unto my family was out of town ;). What would I do differently knowing what I do now? Instead of using the puller on the bearing, I'd have bought a cheap angle grinder at Harbor Freight and I'd have cut the bearing off. This would have prevented the spline from getting mushroomed. Now you know my story.

The bearings and gasket were a perfect fit and seems like a good quality. It wasn't an easy job, to get the old bearings out it took hours of beating it non-stop. It's been a few months so far and it runs great, I will update this review if anything changes. If you decide to tackle this job, it's not a bad idea to get the pressure washer out, the tub was covered in scum.

** UPDATE ** What a huge disappointment!!! These failed shortly after 3 years. I have to tell you, replacing bearing in a LG front loader is a real task, and that when you have ALL the right tools to do the job. The actual bearing pull & place is the easiest part for me. But having to pull the washer and completely disassembling / reassembling it is a royal pain. For me to have to redo this project because these bearing failed is a crime. And it's just my wife and I and we're not talking about a lot of weekly loads. These bearing failed because they are crap - period. You must look elsewhere, spend a few dollars more and get the OEM bearings. It is so well worth it. The original review is below FOR REFERENCE ONLY. DO NOT BUY THESE BEARINGS. ================================================================== I just installed this set and it was a perfect fit for our 12 year old LG washer. Excellent fit and our first load is smooth and quiet. =FAILED AS ABOVE= It is easy to make a bearing that fits. I will let you know if this does not provide expected life. =FAILED AS ABOVE= Like I said... so far - so good. =FAILED AS ABOVE=

Very satisfied with this purchase. The kit arrived quickly and is very good quality. Everything needed for the job was included—bearings, shaft seal, and tub seal—which made the repair much easier. Disassembly of the machine was difficult, but that was due to waiting too long before replacing the bearings, not the product itself. One important thing to watch for is the weep hole behind the shaft seal. Make sure it is cleaned out thoroughly—if it’s blocked, the new bearings will not last. Overall, this is a solid, complete kit, and I would definitely recommend it.

The good is that it fit my washer and worked beautifully. It was a 6-8 hour process. This is not a simple replacement for a mostly handy person. You will likely have to disassemble the entire washer then find a way to pound out the bearings and put them back in. I also broke some random part that I had to order and wait another 4 days to fix. As others have stated watch the youtube videos, they do a good job walking you through the process. Just assume that the parts will not come off as easily as they do in the video. Facing putting another washer in a landfill or spending a small amount of money to extend the life of my washer, I chose to spend a weekend working on this. I replaced the bearings in March of 2020 and they are starting to make noise in Nov of 2021. So that's about how long I got out of them. Not exactly the same 9+ years I got out of the original bearings in the washer. Not sure we will replace a 2nd time. We shall see what I have more of: time or money...

Great kit for the cost. Quality seems good for a non OEM kit. The main seal and both bearings fit perfectly to the spider shaft which indicated that the machining of the inner races are correct which is important to the fit. Time will tell on how long the bearings will actually last.

This is a very nice Bearing/ Seal replacement kit. It fit perfectly and has lasted well. I have read some other reviews that state these are junk, they are not. You have to be careful how you install these or any bearings. You cannot install these bearings by hitting on the inner ring of the bearing, it will instantly ruin them and shorten the life span. I put my bearings in the freezer for 5 hours to shrink them before installation . Then I used the old Bearings on top of the new bearings and hammered on the old Bearing as the driver until new one was seated. The seal has a joining seam where is connected that you will need to install on top of the drum , this is due to the fact that this is the weakest point of the seal and water does not sit on the top of the Drum. These Bearings are rated Washer Duty and are better than OEM as they have rubber seals as opposed to the steel seals that will rust when water comes into contact with them and let the Grease out. Admittedly another failure will occur but you will definitely get longer life out of these. I had 15 years out of the original so I expect as much from this set. It is a lot of work to change these out so if your going in, do it once. Buy this set with confidence as it has worked perfectly for me.

Correspond très bien à ma machine à laver, hormis le joint de cuve qui était trop long..

Leider nicht so langlebig wie angepriesen, nach drei Monaten mit 2 Waschladungen pro Woche , wieder kaputt.... Das ist wirklich ärgerlich

Ottimo prodotto

Came quickly and fit. Seem like good quality, only time and hundreds of laundry loads later will tell ?

Came as expected installed and works perfectly