Univivi IR Illuminator 90 Degree Wide Angle 8-LEDs IR Infrared Light Security Cameras.

I bought this to use with my camera at the shop to light up the area at night. It worked perfectly, and we were able to see what was coming around at night on our cameras. It was however stolen by my son who realized it was the perfect addition to his PSVR2 setup, and now can play in complete darkness with just this light sitting out front of him. He loves it, I'm not getting back, we've had it for nearly a year, no issues. Good Quality, and looks like it should last a long time. It came well packaged, and arrived quickly.

For over a year now I have been experimenting with inexpensive 850nm near-infrared illuminators for use as NIR therapy devices. The results have been surprisingly positive. These devices have actually helped everyone who has tried them – in some cases quite impressively. Over time I became increasingly dissatisfied with my lack of knowledge of what these devices were actually doing, so I purchased a TES 1333 Solar Power Meter to measure irradiance (W/m^2 of infrared energy output) and a high quality multimeter to measure current draw. Due to the “granularity” caused by the spacing between LEDs it is not possible to get accurate measurements of irradiance directly agains the glass face plate of these devices, and the UNIVIVI U8R is especially chunky in this regard. So I took irradiance measurements starting 2” from the glass where the light beams have spread and blended together and at 2” intervals out to 12” and entered the resulting data points into a graphing calculator. Because irradiance diminishes with the square of the distance from the source, I assumed a quadratric regression curve could be closely fitted to this set of points. An R^2 of 0.984 for the resulting equation confirmed my fondest hopes. All this mathematical jiggery-pokery makes it possible to calculate an accurate irradiance value at zero distance from the glass. This is useful, because this value represents the true power density of the device. By popping the back cover off an inline rocker switch I was able to expose contacts for my multimeter to measure current flow. Set the switch in the OFF position, set up the multimeter, touch the exposed leads with the probes. The light comes on and the the current in amps gets measured. The transformer supplies 12DC current, so volts x amps = Watts. I am going to the trouble of spelling out how I did all this because ignorance, speculation, and seller misinformation abound in relation to all of the products in this class. So how does the little UNIVIVI U8R do? IT DOES FANTASTIC! The calculated irradiance at zero distance was right at 1000W/m^2 or 100mW/cm^2. 100mW/cm^2 is a seriously therapeutic dose rate, and you will get it if you put the glass screen directly against a body part. The unit is nominally rated at 8W, but mine drew 0.88 amps which works out to an actual 10.56W power draw which is impressive. So much for nominal ratings. (But I did not check to see if the transformer was actually delivering a full 12V DC. Another day for that.) So, I was pleasantly surprised by this little guy. It comes with a 1 amp power supply, and its light sensitive “eye” is external so you can put a piece of tape over it without having to disassemble anything so you can use it in daylight. It is light and easy to handle and sized just about right for treating hands, knees, neck or other localized areas. It also represents an excellent value on a total NIR energy delivered per dollar cost basis for whatever purpose you might want to use it for. It’s good gear in my book!

It works well. I put a wattmeter on it (I needed the measurement to run it out of a 16-port electrical box) and it pulled approximately 12.3w with the LEDs lit up at night. It is advertised as having a 12v/1a adapter, which would put the device as being powered near the very end of the transformer's power range, however I have had absolutely no problems with it. The transformer and device do run a little warm but not hot. Again, no harm or problem with that. It is smaller than it looks but puts out a nice flood of IR at night. I mounted it under the soffit. The picture on the left shows the patio camera which has a weak IR (only 2 LEDs), so most of the lighting is coming from the IR illuminator, mounted about 6 feet away. I connected with a 16.5 ft cable extender sold by WildHD, although you can also get those extensions in 33 ft lengths that can be daisy-chained. During the day, you will not see much on the IR even with the photo-sensor fully covered -- I had to look very closely with my hand cupped around the edge to see that they were glowing. But it is a whole 'nother story at night -- very obvious that the IR is on (there is no switch, just comes on and off by the photo-sensor). I recently added a second Univivi illuminator to light up the cars in the driveway; as you can see from the pictures on the right, the IR illumination makes a big difference. Be careful about turning off your camera's IR; apparently there is a mechanical switch inside most cameras that blocks IR from *any* source if you turn off the IR on the camera. Think of the Univivi as augmentation, not replacement. Edit 3/19/19. Bought my third one of these recently and it works as expected, even with extender cables. I'm not sure about the range, but where I have this one aimed, I would estimate to be about 50 feet. The other two are still going strong. Edit 12/04/20. The oldest one (approx. 2 1/2 years old) finally had a transformer fail. Illuminator still works great. I swapped in an extra transformer (same 12v/1a output) I had from a camera that now runs out of a power panel and the illuminator is working again. These are definitely outlasting the IR in my cameras, which seem to flame out after a year or so.

Using it for VR. Helps improve tracking in low light areas.

If you are looking to to cover a large outdoor area this nay not work. This is a very well built product and I would recommend it