Low Pressure Drop Transmission Oil Cooler LPD47391 4739 40,000 GVW with Mounting Hardware (Black)

I replaced the small factory tow package cooler since my temps were near 200 degrees and would go over 200 degrees pulling my boat. I flipped the bottom bracket around and used a grinder to notch it so I could mount the trans cooler to it (had to slide the cooler to the passenger side a bit to clear the mount for the PS cooler). I used a brake line cutter to cut the factory lines off horizontal, and then used a brake flare tool to slightly flare them. I doubled up on the clamps where the hose connected to the factory lines. On the cooler, I used pipe thread tape around the fittings to ensure no leaks. Pros: seems to be working good. Put about 50 miles on the truck last night on the highway going 80 MPH with the AC running. Temps never got above the halfway mark from 100 to 200 (so I'm guessing that's 150 or 160 degrees). Install took me about 2 hours in my driveway. I used everything included in the kit (had to cut the hose to fit). Cons: fins are really easy to bend. I had to use a small flat blade screwdriver to straighten some of them out after I was done mounting the cooler. Also, the included clamps are cheap. I've got a tiny drip from the return hose where it clamps to the cooler fitting. I'm going to replace that clamp with a clamp from the auto parts store tonight. My advice would be just get 2 packs of small hose clamps from your local auto parts store and use those instead of the included ones. Also that included screws will strip easily at the phillips head. I used a 10mm socket to tighten them. I snapped one off but I guess I didn't drill a large enough pilot hole for it to mount to the bracket on my 2000 Chevy Silverado Z71. I also flushed the transmission while I had the stock cooler off. I used some clear 3/8" hose and ran it into a bucket. I started the truck and while the dark old fluid was coming out I was pouring in new fluid until it was coming out red. Then I installed the cooler, added more fluid, started the truck, and kept adding fluid until it was at the proper level. I think I flushed about 3 gallons (12 quarts) through it to get the dark fluid out. I ended up buying 5 gallons of fluid total (in gallon jugs from Walmart) and I have about a half jug left after the trans was full. If you don't need to flush yours out you won't need as much fluid.

I have really heavy wheels and a 7 inch lift. This caused a lot of heat build up to my transmission with temps going past 230 with regular driving & go up to 246 with freeway driving (had hard shifts when temps reached around 210) After installing this cooler with some very aggressive driving on the freeway, temps did not exceed 164. With normal driving temps did not go past 156. The shifts were buttery smooth and the truck would go into overdrives ALOT more smoothly. I did prefill the cooler and hoses with Lucas transmission conditioner instead of using regular atf fluid. Install is so easy with the parts and tools. P.S. I bought my own hose clamps, high quality transmission hose and self drilling screws with high temp gasket maker on the threads on the cooler. & radiator adapter part number 357 (brand starts with an H) Chevy transmission temps should not exceed 190 degrees while driving normally like on road trips. Driving hard for short burst should not go over 210 (showing off) and towing heaving loads should not go over 220. I’m curious how these lower temps are gonna benefit me or not in the long run. I was told that with my heavy wheels plus lift made my truck act as if it was towing full time.

Worked Great for a year and a half then leaked from fins luckily I was close to home and hope I didn’t damage my transmission

Bought a camper which we started towing with my 2004 Nissan Armada. However, when we started towing, we noticed the transmission getting hot. After researching, I realized that the factory transmission cooler is not big enough, especially for towing, so I looked into an exterior trans cooler. This one had excellent ratings, so I gave it a shot, and it has been amazing. I disconnected the stock transmission cooler, which is in the radiator and installed this external unit in its place. I am so happy I did. Our trans temp has not been elevated since we put this cooler in. It is well built and appears ready to last for the long haul. Could not be happier.

Got this after seeing the test video on the Half Fixed Garage YouTube channel. The cooler was tested by itself with integrated radiator cooler bypassed. Temperature sensors before AND after the cooler. Fluid cooling of 30-40 degrees while driving and almost 50-60 degrees of cooling at stop lights. Tested in a duramax with Allison trans.

Great cooler but crappy hose. Would recommend getting a stainless steel braided hose and fittings to make it more reliable. I blew the hose after one day. The fittings held but the actual hose failed.

Works great, easy install. I ordered -6 a fittings and ptfe lines. I went from normal 175 cruising and 210/215 in stop and go traffic down to 170 in heavy stop and go traffic and drops immediately to 150s once you get moving again in about 80* Cali weather, car has a built LS engine with 4l80e. I did bypass the radiator completely.

This cooler dropped the transmission temps down on my wife's 2011 GMC Yukon XL Denali to 140-150 degrees steady in the summer heat. Installation required a little creativity. Watch some of the videos online for installing a 40k transmission cooler and adjust as you see fit. I did try to install this cooler with the original hard lines, but could not bend them without feeling like I was about to kink the line and reduce flow, so I wound up installing the cooler with hoses that I slid over the original hard lines. I did heed the warning of the other reviews and not use the included rubber hose and bought some elsewhere. In further research I saw people recommending to install the fittings facing up, however I have not seen any evidence that this is absolutely necessary, but may do so one day.