skoko [2 Pack] Full Body Protective Film Compatible with Rolex Datejust 41mm Ref. 126300 126301 126303 126331 126333 126334, Transparent Clear Skin, Full Protector Coverage, Anti Scartch

Bought it for a gray dial 41mm dayjust with smooth bezel and oyster bracelet. It however is a bit tricky for first time users like me to apply it. But eventually I figured out how to use it. Hopefully my experience can help others.1. Those plastic films do match very well with the watch. So make sure you order the right product and examine pieces to decide where they go on the watch. There are two round pieces, with the bigger one for a 41mm op with no cyclops eye. The smaller piece is for the case back for both op and dayjust. There is another round piece with a cut out which is for a dayjust. Other pieces are easier to figure out. I didn’t use the pieces for inside of the clasp.2. To use the films properly understand that they are not sticky right after you take them out of the water. So you will have time to move it. The stickiness doesn’t come in for a good 4 and 5 minutes. For the crystal, just place the film on it and move around the film to make sure it covers the watch properly. After that I suggest not apply anything else. Wait for 4, 5 minutes to make sure the film is kinda dry and sticky and push the film firmly onto the watch before moving onto the next piece. For places like bezel and cyclops eye, it’s a bit tricky as they aren’t completely flat. Try the bezel first. Again put the film on move it around to make sure it covers the bezel properly, wait for 4, 5 minutes before push it down firmly to make sure it sticks. For the cyclops eye, the surface is curved. One needs to put the film on it but it won’t stick right away. So the film will kinda float only touching the center of the eye. Wait for 4, 5 minutes before pushing the edges down to meet the cyclops eye. You need to hold the film down for about 30 second to make sure it really sticks to the crystal. If the film isn’t sticky enough and moves around you have to wet it again in water and reapply it. The key is to position it right first then wait some time for it to become sticky before then press it firmly to make it stick to the watch.3. The watch case back is similar to the cyclops eye so need to be patient. It is easier with the clasp and bracelet pieces as they have flat surfaces.4. Make sure all film pieces are clean you can always wash it with water. And the watch should be clean. Press firmly at the corners and edges as that’s where dust might get it.Patience is key in this application. Took me two nights to get it done right. If you do it right you can hardly see the film.

Its perfect. A must! Cant tell theres a protective film.

The media could not be loaded. I just installed it so I don’t know the long term quality but I here’s my thoughts…Watch: 126331 Datejust 41mm JubileeLooks better than expected, doesn’t stand out with the naked eye, I tried focusing my camera from certain angles to show that it was on. I had trouble closing my watch with all stickers on, so I had to remove one (shown in photos) so that I can get it to close. They may be too thick on the inside of the clasp for my watch to grab and lock closed so I removed it and now it’s closing fine. The film is thick enough to protect from normal use scratches. I’m actually happy that it is clear enough where you don’t notice it on the dial. I was going to skip out on that one because I thought it would show too much and ruin the beauty of a Rolex but you can’t even see it unless you’re looking for it!!

I was hopeful for the product. Pretty hard to apply, not as easy as on the videos. Now you know why it comes in twos, you won't apply it the first time. Didn't even come with tweezers, what company does that? But they provided the water and detergent container. For the price, it's so frustrating of a product, it does not come with the tool to apply it on. I tried, but this is going back to Amazon.

I have this product on two of my very expensive watches. It fits well and was relatively easy to install. However the stickers don’t last long with consistent wear and the edges start to get dirty and tattered looking.

Very happy with this product because it is invisible and fully protects my watch. Unless you know there is a protection on the watch, you will not notice it otherwise. Definitely worth the money to prevent scratches and possible glass cracks. Took me about an hour to apply all the pieces. Results are in my pictures.

The quality is awesome you have to be careful during the installation process no rush, but once it’s done you even see it on the watch 5/5

I understand the protection it provides, but was very difficult to apply evenly and when applied to the face you could see the protector on the angle. I ended up taking mine off because the sides ended up becoming loose and could visibly see the protector.