Electro-Conductive Adhesive Glue for Heating Circuits Printed Circuit Boards 2g New

Worked like a charm for repairing the degraded conductors on the membrane connector of my IBM Model M. It is not glue. It is paint. When fully dry it is quite friable and has no strength; it could not be used successfully even as weak glue, but as paint it works a treat. It begins to dry very fast, and becomes too thick to brush within a minute or so of dipping the brush, so you have to be a bit quick and use only the tiniest amount at a time. But you only need the tiniest amount anyway, so that's not much of a problem. Do not be alarmed if you still measure a high resistance immediately after putting it on. The resistivity drops slowly over the period after application, and it takes maybe half an hour or so for it to become fully conductive.

This product was advertised as an adhesive electrical connducter . It has zero adhesive elements. It’s a paint with silver particles. Very mid leading

I have some lines on my car rear glass that don't work. There are about 4 lines where the contact has come away in places. I managed to paint this stuff on to about 2 lines ok , but only one line seemed to work the other did not. The issue is that you only get 2g so there is simply not enough to recoat and probably get the line working correctly. It is too expensive to just buy more of this stuff to paint on as I would need loads to recoat and do the other lines, probably cheaper to replace the glass. Hence only 2 stars as no value for money really. If you only need a small bit then should be fine .

A chip had come away in my remote car key fob. I bought this and used it to fit the chip back on (there was no chance of soldering it). The term "adhesive" is a bit misleading as the stuff is very brittle so it doesn't have much gluing effect; any force applied seems to crack it. But once I had tested that there was contact with the product a dab of real glue on top seems to have done the trick. Given the price of a new key this was a good deal. You might also need to find something finer to apply it with if you are using it with circuit boards - the supplied brush should be fine for larger work. [I should add, that about 3 weeks after my repair triumph, my front door slammed shut on the car key, bending it through 90 degrees. After careful hammering back, the key worked for a few days before shearing off in the ignition. After a helpful AA man got the key out, I then had to pay for another key which had space for the proximity chip but not the remote chip. So I now have my repaired fob to open the car and a new key (pricey) to start it. So the saving was not so great - but that's no reflection on the product - just a reflection on the fact that fate does not allow you to get away with anything.]

I had a fine wire in a clock snap so I needed to fix it. I am not confident with very fine soldering so I thought I would try the electrically conductive glue. The item was despatched very quickly and arrived in a couple of days. It was very easy to use and I could safely glue the joint. The glue is not a speedy "super glue" type of glue so you need to be patient and use some care but it was far easier than trying to solder in a tight space. Take your time and give the glue time to cure and you will be fine. I am very pleased with the speed of the service and the end result of the repair. Will happily use this company again.

Bought this to seal a few breaks in the wire heater circuit on my back window on my 05 corsa. This product did not work? The brush provided isnt good= needed to be much finer for such a precise purpose.

I’ve tried similar products before, attempting to fix a broken connection to rear window demister element. Unlike the cheap Chinese products this sticks well to the glass, and carries current well so has at long last fixed the issue. I used a little araldite type adhesive to stick the tab to the window then made the connection with this, in addition to repairing a couple of broken tracks. Good stuff, would definitely recommend. Take the time to thoroughly clean surfaces first with an alcohol wipe for best results 👍

Sadly this very expensive solution (pardon the pun) had no adhesive strength when used to stick the contacts back on the rear screen of an Aygo. Although surfaces were scrupulously cleaned and the adhesive left to set in a dry and warm environment for 48 hours the connector simply dropped off when gently attempting reconnection. This was very disappointing, particularly at this cost. Whether it works in terms of electrical conductivity I didn't get to check but I would sincerely hope so! So in short where mechanical bonding strength of copper to glass is hoped for, forget it! However, if you just want to apply static to reinstate a circuit track it will probably work fine. In my case a costly and disappointing purchase.

Reparation de circuit de dégivrage de lunette arrière

Funktioniert einwandfrei nur kleben, naja. Habe es bei denn Kontakten bei denn Hintertürgläsern für die Heizung bei meinem Bus benutzt. Hat kurz gehalten. Vll liegts dran das man die Tür zuhauen muss.

Acquistata per prova per riparare lo sbrinatore posteriore del mio veicolo. Ho pulito bene e sgrassato il vetro con dell'acetone, delimitato il segmento con del nastro isolante, agitato bene (2 minuti) la boccetta ad ogni passata (3 passate in tutto a distanza di 10 minuti una dall'altra) e poi lasciato asciugare per 24 ore (a dire il vero ho avuto modo di provarla diversi giorni dopo). Tutti i segmenti (8) hanno ripreso a funzionare. L'unico (mio) errore è che ho lasciato poco margine tra il nastro isolante e il segmento e nel rimuoverlo ho rimosso anche la colla da metà dei segmenti, che ora necessitano di un altro intervento (ho ricomprato un'altra boccetta anche se ancora ne ho di quella iniziale). Per il prodotto in sé mi pare non abbia nulla da invidiare ai gemelli di marche più note.

1st the glue didn’t dry very fast. I had to hold it for about 15 min it still wasn’t dry so got some tape to hold the piece in place while it dried. Then it never worked