HH-66 Toluene Free Vinyl Cement, 118 ml can - RH Adhesives

Brilliant stuff, I used this cement to repair a Lay Z Spa hottub. Other glues and patches could not hold, but I applied HH-66 in multiple layers, then followed by a patch. The repair has held completely for weeks. I would highly recommend this product for inflatable hot tub repair.

Did a great shop repairing my SUP

Strong bond.

This specialist glue is excellent for bonding vinyl for a permanent fix.Because it soon dries,if using on a large area,it is best to bond small sections at a time

Glued my paddle board with this & first time I had the pvc misaligned, I couldn't part this glue once it had dried, started ripping the material. Fantastic glue.

Very strong - doing the job. Eye watering price though

This is insanely overpriced considering how little you get, and how much you need to apply to get proper adhesion. I purchased the 118ml can, thinking that it should be plenty for a small job. The can is very small, and not full. The instructions say to apply to both faces, and wait for it to become tacky. Most adhesives can be used quite sparingly, but when a small amount is applied, the glue becomes touch dry almost instantly and doesn't go tacky. The resulting bond was very weak, and could be pealed off easily (even after 24 hours). I needed to brush this on quite thick to achieve an adequate bond. I ended up having to use two or three times as much glue as anticipated, and did not have enough to complete the relatively small job. I would not recommend this adhesive. Instead, I wish I had purchased a stronger two-part PVC adhesive from a marine store. This would have performed much better and cost significantly less than this HH-66 product.

Great bit of kit for little money does the job

Cette colle a été utilisé pour coller des d-rings sur paddle collage rapide reste à tester si cela tient et le petit pot n’est pas bien grand 😂😂😂

I came across this HH-66 Toluene Free Vinyl Cement, in the 4 oz. can. After doing extensive research online for my specific project. I purchased a used, but in excellent condition, full size, tonneau cover for my F150. I have a tool box in the rear and I wanted to cover the exposed bed. The tonneau cover had a length of 72" and i had to shorten it down to 45". As a handyman by trade and an RC hobbyists at heart. I took the tonneau frame apart and put it back together, almost achieving a factory finnish. 1. I performed a small test on two strips of vinyl. I didn't clean them (intentionally) because I wanted to test the cement on unclean surfaces to check the level of adherence. The cement bonded phenomenally! 2. Prep your surfaces/wipe both sides with alcohol before applying the cement. 3. Please note: The cement dries as you brush it on, if possible, I suggest working on small manageable sections like 5" to 10" sections at a time, brush on quickly. Once a desired section is complete, move on to the next piece immediately! "Do not waite to bond the pieces together after brushing the cement on them. Once the 2nd strip is covered in the cement start bonding the ends together so they don't dry-up on you in the process....if they dry, your going to be left with a weak/ poor bond, the ends may lift or you will end up with air bubbles trapped between the vinyl 4. Wetter is better! You need both sides to be tacky wet, not tacky dry. I can't stress this enough 5. Press and hold for a few minutes, I used duct tape, blue painters tape and a variety of different size binder clips for my application and it worked great, get creative 6. Take your time, my specific project took roughly 3 days. I worked on it mornings and late evenings. I wanted to finnish my project but I wasn't in a rush and it turned out great! 7. The smell wasn't overwhelming for me, (I have worked with an array of chemicals) but if your sensitive to smells, yeah, it's best if you work outdoors, a garage, a shed, or a porch or just crack open a window. 8. My seams bonded extremely well, tight, no water leaks, no issues, no lifted ends. 9. Clean up is a snap! If you don't have thinner just use your 91% rubbing alcohol on a rag and wipe everything clean, it will break down the cement the same way. If you made it this far, I hope the small details described in my review will help you during your next project (s) i would use this on flexible thick vinyl products, not the cheap flimsy stuff. Preferably on tonneau covers, pool covers, air mattresses, vinyl tarp repairs, etc. Just to name a few. Also, if you intend to use this cement on PVC pipes, don't! Just go to your big box store, they sell a kit specifically designed for PVC pipes. Reminder: Always try a test piece first, before moving forward. This way you will be able to move forward confidently. Take care all, just a handymans honest perspective.

Ho usato questa colla per riparare il mio SUP. Super resistente, facile da stendere e soprattutto fa ciò che promette.

ok

This product works as advertised on SUP. I had a small nick at the factory seam between top and bottom halves of my SUP. I followed the directions and first glued the seam back together as best I could and then inflated the board to low PSI to establish the shape for adding a larger patch (using SUP manufacturer patch material) to overlap the seam and serve as a back up since I doubt I could repair the entire seam separation. Added some more PSI but still on the lower end for the next hour. Then took it up to full pressure and let it sit overnight. Holding pressure really well and this board is useable again (before repair would be un-useable ion 10 minutes tops)! Absolutely recommend this glue! I will adjust the review if down the road the repair fails but I do not anticipate this.