Tyger Auto Fender Flare Compatible with 1999-2006 Chevy Silverado GMC Sierra 1500 2500 3500HD; 2007 Classic Fleetside, Fine-Textured Black Paintable Factory Style 4pc | TG-FF6C4218

Near perfect fit. Couple small gaps. Looks great. Not a big plastic push pin fan so I replaced three of the pins on the back fenders to bolt and locknut. Replaced three of the front push pins with ones with an interference fit P/N Item #138260 Model #881200. Got them at Lowes. Actually had to tap these in with a hammer.

They fit very well , but the first hole seems to be out of place but they look good and are easy to install.

These flares fit my 2003 Sierra really good. Very simple to install and they seem durable. Really good for the price.

Originally, I purchased a different brand for around $60. They arrived. Complete disappointment. They didn’t fit in any way at all correctly, plus, they were smooth finish and not OEM style like the description said. Then I found the Tyger brand. More expensive but looked more like OEM and they were made of the more flexible nonbreakable plastic. They arrived and I was pleased with the look. The texture and color matched the other items on my truck. The kit includes the pop-lock pins and the fenders. There are no screws to mound into the fender or 3M tape that adheres it to the truck. They simply slide into place and the contours matched the body lines (the DNR brand did not). The predrilled holes are lined up with the holes in the edge of the fender well. Most of them did. Three of four flares had one or two at the top that did not line up. I had to find the hole in the fender and redrill the flare. Not a hard task but it’s the reason I gave it a 4-Star. The flares lined up with the fender fairly well and compared to the OEM version, they are a very close match. The front passenger side flare did not conform to the fender too well. Once in place, there was a gap of about 1/16” between the fender and the flare. It looked enormous. However, removing the pins and adjusting how for into the fender well the flare went closed the gap and looked more like a snug fit. Then I had to drill new holes in the flare to match the fender well holes. It was about a 5 minute adjustment - nothing major. Total install time was about 45 minutes - I took my time and made sure I installed them correctly. Overall I am well pleased with the product quality, durability, and improved looks it has made to may 2000 Silverado. I’ve included a “before” photo which includes the original Silverado rims. Then the “after” which includes my replacing the rims with 2020 Silverado 18” rims.

Couldn't ask for a better fit on my 2002 Silverado, but some adjustments were needed. These fit perfectly into the wheel openings, no slop or gaps, snug. A person could stop right here and just screw them in with a set of stainless screws as you would with a set of mud flaps and forget the buttons. (In the end if the buttons fail, this will be my permanent fix). And be done with it. They should be pulled tight to the top of the wheel opening, then visually find which vertical button will hold it in place tightly at the top. My top buttons did not line up and needed to be slotted slightly so the hole in the flare would match the hole in the fender. This was the same on all four flares. The top two holes did not match without a bit of adjustment. Bear in mind this is also an opportunity to put inward pressure on the flare for a tighter fit while checking how much and in which direction the new hole placement should go. This will keep the flare tight to the body without any gaps. I used my Dremel with a high speed cutter bit #194 on low speed to slot the upper mounting holes in the flare roughly 1/2 of the hole diameter and slightly angled to the outside (to increase tension and close any gaps or looseness). I had a single plastic pin securing the flare in one of the vertical holes that fit best. The instructions suggest installing the top pins first and working down. These did not line up in my case, and required slight slotting by being roughly 1/2 of a hole off. Better to find the best vertical hole after pressing the flare tightly upward into position. The gist of this is that these flares can be fitted perfectly with only minor adjustment. As far as the buttons included, hope they survive a winter ice load but can be remedied with some stainless screws for a permanent fix.

I don't often write reviews unless a product exceeded my expectations. This is one of those. Delivered in two days, and took all of maybe 20 minutes to install all 4 fender flairs on my Silverado. Super easy and they look fantastic. All for $75.00 If you're thinking about these, go for it, you won't be disappointed.

His my rust and look oe which was exactly what I was going for! Fit was surprisingly good. Didn’t come with hardware though, luckily I have all kinds and made it work

Installed these like many others to cover up minor body damage or the inevitable rust that will start. 3 installed very easily but one was a real pain due to the holes not lining up with the holes on the wheel well of the truck bed. Took some extra effort to get it to fit and stay correctly. All in all these are pretty solid. Will see how they last over time. 1.5 year update: these have held up very well with zero issues. None of the plastic mounting pieces have gone missing and no deformation or discoloration has occurred to the flares. 10/10 recommend!

These fit very well. Installation was straight forward. Seems to be good quality

This Fender Flares do not fit SILVERADO 2500/3500 models. Just 1500. The 2500/3500 have wider wheel openings. Could not mount them to my 2010 2500HD. Quality of the product is ok.

Excelentes y fácil de instalar

Fit my 2007 Sierra 1500 Classic just fine. Covered the rusted wheel wells and now looks so much better. Installation went smooth into the factory pre-drilled holes. No complaints.

I installed these on my 2002 silverado to hide the rust around the wheel wells. Looks great. They fit surprisingly well, just had to add a few metal screws (underneath, not on the face of the flare) to keep them tight to the truck body. Total install took about 40 minutes. Very happy with this product.