15-73952 (89018374) Heating and Air Conditioning Panel Mode Door Actuator

Works great. Exactly like the OE part

UPDATE 01/23/20 I've been using one if these as a mode actuator and another as a blend actuator for a few months now with zero issues. No calibration loss in an auto climate control application, great OEM made in Korea product. ~~~~~~~~~~~~~~~~~~~ UPDATE: 11/08/19: USED AS A BLEND DOOR ACTUATOR This has been running well as mode actuator on an '03 Suburban for a few weeks. I've heard of other instances of this same part being used as a temperature (blend door) actuator and I decided to take a shot and use it for my passenger side blend door actuator with auto climate control. The track that comes with this model pops off the actuator and you are left with just the unit. I was a bit apprehensive about using it in the blend door position, but I just finished the job and it calibrated just fine as a blend door actuator using the same step list below. I used this in place of the original GM p/n# 52402588 that was removed. The job itself took me about 4 hours since I had to remove the passenger airbag and the onstar module takes up a lot of the work space so it was a very tight area, and I did disconnect the negative battery cable for this. I used a pass through ratchet with a 5.5 MM socket to get the mounting screws off, there were only two screws, but a nightmare to get to. I will update in a few weeks to make sure I have no issues using this mode actuator in a different capacity. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ORIGINAL: First off, yes, my product was made in Korea, but this does not keep it from being a genuine product. Do some research people. NOTE: REMEMBER TO FULLY INSTALL THE ACTUATOR, DON'T SLAVE IT IN BY JUST PLUGGING IN THE CONNECTOR AND TURNING IT ON, YOU WILL OVER EXTEND THE INTERNAL ACTUATOR GEARS AND MESS IT UP!! I used this as an actual mode actuator for an '03 Suburban with auto temperature control. The mode gear is hard pressed together but it will come apart , just don't pry it side to side, straight up will do just fine. I didn't use the new gear, just the actuator, but after performing the hvac recalibration everything worked great. My mode was stuck in feet only, now it works in all settings. Note: the mounting bolts were 5.5 MM. DISCLAIMER: FOLLOW RECALIBRATION STEPS AT YOUR OWN RISK For manual systems it does not matter where the a/c controls are set but if you feel the need to do something, turn the blower switch on (I prefer speed 3) and set the temperature sliders about .5″ to .75″ from full cold. For auto systems, press the auto button, with the key on. Turn the ignition off. Remove the HVAC/ECAS , 10 amp fuse in the underhood fuse box* or disconnect the battery for one minute. *Fuse locations can vary from year to year and between different models. Install the HVAC fuse or reconnect the battery. Start the engine. On systems with auto a/c controls the controls will default to 74 degrees F when the ignition is turned back on. DO NOT TOUCH the a/c controls. Let the engine run for 1-2 minutes. Turn the ignition off for at least 10 seconds but no more than 30 seconds. Restart the engine and then test the a/c controls.

Installed on a 2003 Suburban. The actuator seems to be good quality but it's not exactly identical to the original unit. The original actuator was assembled using screws, the replacement actuator just snaps together. Cheaper manufacturing. We disassembled the bad actuator and the large drive gear is plastic and was cracked causing the gear to slip. Removal and installation of this part is NOT easy due to learning curve. Second time would be easier. When installing, take the plastic cam assembly off the actuator and position the cam assembly on the heater box first. Then carefully rotate the cam assembly as needed to line up with the clocking of the actuator shaft bore and push the actuator onto the cam assembly. Install screws. We just started the truck and the actuator began working properly with no problem. This fixed the problem where the air flow was stuck on defrost.

Exact quality part as the one I removed from my 2005 2500HD. This mode actuator is on the driver's side above the gas pedal. Cam plate should be installed first, check that all vent directions work freely before installing the actuator by holding the cam plate flat while turning between defrost, floor and panel. Viewing the actuator from the gas pedal side, full counterclockwise is for full panel. Tick marks to the left of center. Rotate the cam plate to align the actuator post then you can rotate the actuator and cam plate together to get the two screws aligned. When I first installed this, I could not get defrost until I Googled it to find the reset procedure. To reset, pull the HVAC fuse for 30 seconds, replace it. Fan off, mode to panel, start engine, immediately turn on fan and ac, actuator will blow air from defrost then back to panel, turn off engine. After a few seconds, restart engine and test mode directions. All directions should now be working properly. Good luck! Hardest part is installing the cam plate. Sneak the plate over the gear to engage the cam follower that is on the top of the gear, then sneak the outer cam follower into the outer track, the upper screw post also has a track. This track helps indicate the maximum movement of the cam from defrost to panel air flow.

Took me some time to get to installing this part. Two issues with it: 1) couldn’t get the bracket off the actuator motor which made it very difficult to install. 2) Actuator motor does not work. At first I thought maybe I had installed it incorrectly but then I took it out and plugged it in and tried the different modes with no load on it the motor did not move at all. So essentially I was sold a bad part and now I’m stuck with it because I’m beyond the three days by 5 days. Now I have a dashboard that’s torn apart and no replacement part...

Good deal Good price

Five stars for this because: It is identical in fit and finish compared to the OEM from my 2006 Chevy Tahoe It cost significantly less than a new OEM replacement part from the dealer, or from NAPA or from... It functions precisely as it should. It has been installed for a couple of months now and is still working exactly as it should. TIP: Be aware of the difference between the "Mode" door actuator and the "Blend" door actuator. The blend door regulates HVAC air temp while the mode door directs where the air is delivered (defrost / dash / floor / etc.).

This product worked well when installed and was direct match to the existing unit. Remember to go through the re-calibration procedure after installation. This simple procedure is easily found on YouTube and other sites. This installation was on a 2005 Silverado 1500 truck. The vehicle manufacturer has these mounted in some pretty tight spaces so installation is a bit difficult.

Solved my problem of heat blowing from all vents and selector not working.

Es muy parecido al original pero el material es más sencillo

يعمل بشكل ممتاز منتج اصلي gm

Good replacement part. work has intended. The p/n on the sticker is not the same has the original but it works just has well.

Works well.