PneumaticPlus PPF3-N02B Compressed Air Particulate Filter, 1/4" NPT (High Flow), 5 Micron, Poly Bowl, Manual Drain, Bracket

Good filter and will buy again if needed.

The media could not be loaded.  I used this in conjunction with a homemade compressor aftercooler and the result is incredible! So good, in fact, that I may have to purchase an automatic-draining unit because otherwise I have to stop what I'm doing and empty it constantly. It's completely full of water after 2-3 fill cycles. The idea here is to cool the air charge as quickly as possible, and as early as possible in the system. When you add an aftercooler and put the dryer between the cooler and tank, it helps to condense and remove the excess moisture long before it reaches the air hose. Since I've done this, I have ZERO moisture coming out of my air tools, and almost zero moisture draining out the bottom of the compressor tank. I have yet to run a paint gun on this setup, but will be doing so soon.For those wondering, the aftercooler setup is simple... a box fan, the largest cheapo transmission cooler I could find, a roll of 3/8 aluminum fuel line, some compression fittings, this dryer, and some creativity.

First one had a slow leak. I called them and the immediately sent me another one, it worked great. The7y are small light, hold 250 PSI, filter down to 5 micron, and works great. I installed it on my Jeep firewall to filter air going to my ARB locker. I highly recommend them.

I bought a new compressor and always had issues with moisture in the lines. I had filters of all sorts but still moisture in the line. I decided to try this filter x 2 and added a new pressure regulator with filter as well. So 3 in-line filters with my new 10 gallon compressor (see review for HULK 10 GALLON) and NOT A DROP OF MOISTURE! These are great little filters, inexpensive and of vary high quality! Great product and price!

This air line filter is solid and well made. It's compact enough that I was able to easily install it inline on my DeWalt 30-gallon air compressor. Servicing the filter is a no brainer. It's perfect for occasional use of my air impact wrench, which requires 90 PSI.The unit comes with a steel bracket to use as an optional wall mount. Keep in mind that if you chose to use the wall mount, you will need an appropriate length whip hose between the filter and the air compressor. Depending on your setup, you may need other 1/4" adapters to complete the installation.This unit does not ship with any connecting adapters.

So far so good, bought these to keep water and possible oil out of my airbrush line from a 30 gal oiled compressor. I have the 1/2 post air compressor and the 1/4 at the terminal end. Had to purchase 1/2 in to 1/4 in reducer separately for the half inch model.Posted a pic for size comparison since seller failed to do so for some reason.I’m not sure if this was the issue that others have been complaining about with leaking but the 1/2 leaked from the release valve at first but once it fully pressurized and the rubber seal on the bottom fully seated, it’s now air tight.I tested it out in ~70% humidity, the filter first in line air felt a little moist from the release valve, the second seems completely dry and the air from the brush is completely dry. So I would say definitely worth the purchase.Summer time will be the real test though, will update then if they under-perform

Works just fine as a pre filter for my system. I up sized to the 1/2 npt size to have plenty of capacity for water, this should hold close to a half cup.The threads were unusable on the outlet side, they were gritty, and tore up the thread sealant tape. The fitting only threaded in 2 turns before binding up.The inlet side was better, the fitting turned about 5 turns, and sealed up just fine.I took a NPT tap to the outlet, and got 2 more turns before the threads cleaned up, and all is well now. I would have expected this to be caught at the factory.The inlet cleaned up a little better with an extra half turn with the tap as well.

While looking through the items throughout Amazon, I picked this PneumaticPlus PPF3-N02B because of the price. Comparing it with all the others this item had better features than most others. It was very easy to install and it's functionality, so far is been trouble free. What I dislike the most about this item was the very poor instructions that came with the item. Not much to say in the instructions, but I would have liked a little more clarity. I could not find a section on the instructions on how to drain the filter or find somewhere about assistance.

Works well. Easy to drain

Works great instead In inline with my air compressor

Dry air from the time of install

Item returned before use due to change of plan but initial impression was. - VERY NICE INDEED!

Clearly advertised in the item description, max input pressure 250psi. When I physically check the unit on the side of the bowl shield it says max pressure is 145psi. Needed the unit to get my compressor working, now I have to go and search for another suitable unit. What a waste of time and effort. Going straight back for a refund. One star due to incorrect / misleading specifications.