TUSITA Magnetic Charger Compatible with Withings Scanwatch | Scanwatch Horizon Smart Watch - 1M

Works like a charm with my Withings watch, and a tenth of what it would have cost from Withings directly.

The charger works fine but will off-position your dials every time you charge and you have to recalibrate whenever you charge. I bought one and immediately regretted after one charge, I recommend getting the original one over this, as it isn't that big of a price leap anyways.

Keeps my Phone well charged!

The magnetic part seems to connect better than the charger that came with my watch. I bought this because I couldn’t find my original charger, but I now use it more than my original charger as it doesn’t randomly disconnect as much as the stock charger.

I got this to replace a charger lost during travel. It works and is cheaper than the Withings card;e, but does require resetting the hour and minute pointer (time) after charging! I was told by Withings support that a magnet in the wrong location can cause this. I have bought a Withings charger cradle since then and can confirm that it does not have the issue.

It works and yup, - the analog hands are wonky after charging. So you do have to go into the app, and "set the time" to spin the app clock face hands to 12 for it to display correctly. Doesn't affect the actual time on the digital portion - just the analog hands.

Replacement watch charger which arrived on time and is what I expected. No issues with device charging my watch.

The Very Bad. The very Bad is the magnetism is so strong that it freezes the hands of the watch while charging. This is the second third party seller I purchased from and both units cause the watch hands to freeze when charging. The watch can be reset but I have to believe that over time this repeated type of restriction will cause permanent damage. The Good. The positive side is that a least someone is selling these because Withings sight when checked was not only out of stock but charging more than twice the amount. Also, there is no guarantee that their replacement won’t come from a third party and have the same issue. When making the second purchase from Tusita I did so knowing it was very likely that I have the same problem I had with the first seller. However, viewing the pictures that Tustia presented in their ad of the internal parts, I felt there might be a fix and there was. The Fix! There are two magnets inside the unit if I could reduce the magnetism or the size of the magnets, I figured that would be the fix. I was right but the how to do this depends on what you have available. The easy solution would be to pass unit through a demagnetizer until the magnetism is reduced enough. However, I don’t have nor did I desire to build a demagnetizer. So, I then placed magnets on the end of a hammer and whacked onto concreate. I wanted to disrupt the strength of the magnetism but the material is not a hard metal and shattered to pieces. The positive was there were still a couple of pieces large enough to use. So, I placed the pieces back inside the holding channels and tried to see if the unit would still bond with the watch and it did. Note: you have to set the poles of the magnets correctly so multiple inserting will likely be required as it was the case for me. I finally got the magnets position and glued it back together. The unit still had plenty of magnetism and bonded fast without freezing the hands. I would suggest breaking magnets with pliers and using one third on each side. Yea I know not the best solution but currently for many it may be worth attempt and the effort. Whole process took me about an hour and cost was low enough to try. Good Luck!

Très bon chargeur ! J avais un doute suite aux anciennes appréciations ( aimant trop puissant, heures changeantes lors de la charge). Soit le produit a été adapté aux critiques soit j ai de la chance. Après une dizaine de chargements ...aucun soucis ( vitesse de chargement , aimant de fixation ...). .

Tut was es soll... Hatte das orginale Lade-Adapterkabel von meiner Scanwatch verbasselt. Hängt bei mir an einem USB-Ladehub und funktioniert. Kabellänge könnte gerne 50 cm länger sein. Achtung: Die unterschiedlichen Withing-Uhren benötigen unterschiedlich Lade-Kabel. Dieses scheint speziell für die Scanwatch zu funtionieren. Die z.B. anderen Steel-Modelle benötigen wieder andere Lade-Adapter.

Works great with my withings watch. Thank you

È perfettamente uguale all' alimentatore originale. Provato, funziona perfettamente.

This item solved the problem of my Withings watch not being charged. It was good quality. The magnetic strength was very good and entirely compatible with the watch. It fitted perfectly. Recommended