WL133 Drill Press Laser Crosshair – Long-Lasting Easy-Use Portable Drill Press Guide – Thin Precision Laser Alignment Tool – Perfect Drilling Machine for Accurate Setup Where Needed

Installed and setup in less than 15 minutes. So far, I’d say this was worth every penny. Wish I’d bought it years ago. Fits multiple sizes of drill presses regardless of column diameter and throat dimension. It’s very easy to dial into your drill center. This makes positioning your workpiece easier, faster and more accurate. As with the other Wixey products I own, the build quality is very good and is a great value.

set up a super easy I don’t understand what any of the bad reviews are for it . works well. I mean it’s not like you’re gonna drag it behind your car at 50 miles an hour. I have it on a wen bench top drill press that I changed the whole base over to so it’s a little customized, but it’s still a bench top drill press says zero no problem. the only downside is if your vice cradle walls are a little too high than your material too much it’ll block the laser because the laser is not coming straight down at the material it’s coming in at an angle, I gave it five stars because it’s doingexactly what it supposed to do

The Wixey Drill Press Laser works very well. I had no trouble mounting it, or adjusting it to get repeatable accuracy to about 1/32". I would have given it 5 stars instead of 4 except for one annoyance. I found myself constantly forgetting to turn it off, and running the batteries down. I finally fixed that problem by replacing the two AA cells with a 3V AC-DC adapter. To do this, I had to install a suitable jack in the rear of the battery compartment and move over a few wires. (see photo). As claimed, the device can be adjusted to produce crossing lines independent of the height of the workpiece, It does so by producing two crossing planes of illumination, each approximately perpendicular to the drill press table. The “z-axis adjustment” changes the tilt of each beam to make it perpendicular to the table. However, the supplied adjustment procedure is slow and inaccurate. I have found a better way (see photos). Set the table to be about 12” from the lasers. Place a small mirror on the drill press table so that each beam is reflected upwards. Use small object (approximately 4” in height) to hold a small piece of wax paper to intercept both the direct and reflected beams. If the “z-axis” is not properly adjusted each beam will produce two parallel lines - one line is from the direct beam, the other from the reflected beam. Adjust the “z-axis” screw so that the two lines coalesce. At that point the beam is bouncing perpendicularly from the mirror. Repeat for the second laser. The whole process is very fast, and there is no uncertainty as to when the two lines overlap.

I installed this laser unit on a Shop Fox W1668 drill press. It seems to be well constructed and it was pretty easy to install. It always helps to read the directions. To calibrate it, I used the mirror method that Ira described in his review (he made it easy to follow with included photos) and that went very well. I lined up the z-axis on the waxed paper, then made my drill bit mark and lined up the x and y axes on the mark according to the enclosed directions. I then lowered the table about 10 inches, and lo and behold, the X was less than 1/32" off. That's gonna be accurate enough for anything that I need to do for sure. I have been using it daily for a week or so, and it's made my drill press time more productive. The lasers are bright enough that they can be easily seen in a fully lighted space, and though the lines could maybe be finer, they are accurate enough that I have no concerns. Good product and a very nice upgrade to my drill press. I had known about this unit for quite awhile, but was reluctant pull the trigger. Now i wish I had done so many moons ago.

Great upgrade for my 30+ year old floor standing Craftsman drill press. Aligning the lasers wasn’t too difficult and yes, the laser cross spot stays put despite the height of the table, when adjusted correctly. The laser blocked the built in press work light so I added a spare small 12v led flood light. Wired a 12v power supply to the light switch on the front of the press to power the light. Of course the light was too bright and washed out the lasers so I added a PWM dimmer. Since I now have 12v power available I hard wired a buck converter to the Wixey so it now turns on and off with the front light switch. The buck converter is mounted to the bottom of the Wixey plate so it’s not visible in the picture. Very happy with how everything turned out and very happy with Wixey laser crosshair.

I installed this on my Elihu CNC Plasma Table in less than 5 minutes. Drilled 2 new holes in the Wixey mounting bracket to match up to my torch head and DONE! Very easy install and looks good too! Wixey laser adjustment is very easy to get it dialed in.

Excellent product

I added this laser guide to my new Nova Voyager floor standing drill press. It is a nice addition that comes in handy from time to time. It is accurate and maintains the correct position, even when the drill press table is moved up or down, if installed according to the easy to follow instructions. Many reviewers here or people answering questions above say it has to be readjusted if you move the table, but that isn't true if you just follow the instructions. It only takes 5 minutes. I'm only giving 4 stars, however, because I would like the product even better if the laser lines were 1/2 or 1/3 thinner than they are. As is, I use the laser cross hairs to get (very) close to the drill location and then dead on by lowering the bit to the work piece before turning the drill on. Also, it would be a much better product if it turned off automatically after some specified time. As is, if you forget to turn it off, it will eventually exhaust the batteries. Glad I bought it, but it could be a little better.

思っていたより良い商品でした。

Pour perceuse à colonne.

looked great, did not work as well as the you tube video after a month found pieces of it on drill press base the laser adjusting nuts had started to disintegrate.