Malco PRODUCTS C5A2 Impact C5A2 Power Assisted Crimper

Crimper works great, Clearly a quality product. I had issues with delivery but I believe that was nothing to do with the product or seller, that being said the delivery for a replacement was prompt

This is much faster than hand crimping, and far easier on your hands and forearms. I can crimp a 10" duct in about 10 seconds, while it's already mounted. Because this goes on the end of your impact, it can spin 360 to modify duct that's already in the air, as long as you've got 2+ inches all of the way around. Just don't go over a seam, it says so right in the instructions. It takes a few tries to learn the best way to get it fully engaged on the pipe, I just go forward a couple of clicks, then reverse back to the starting point, and it's ready to go. I am using it with a Milwaukee M12 Surge impact, so it's noise level isn't too bad. With a standard impact, it will likely be quite loud, especially when amplified by uninsulated ducting

Working good, but no long . Used 3 days for crimping 30 GA pipes 10", 8" and 6" . Used with dewalt impact driver . I need it to work right now, but it's broken. Now need replacement drive shift and wait then it comes. if this repeats, I will constantly look for a replacement from another manufacturer or buy another model .every 3 days to buy new replacement drive shift too expensive.

Good product

I have been wanting one of these for a very long time. I finally decided to put down the money and get one and trust me, you already know without even using one that it's so much faster than crimping by hand. Well worth the money spent. They work a little better once they start to break in. In the beginning it almost over crimps but I'm not complaining. It's fantastic especially if you have arthritis or hands that are over 45 years old LOL.

I work in the heavy commercial and industrial fields of HVAC dry side (duct work and related equipment). As I have gotten older my hand grip is not what it used to be and crimpers often take a tole on my wrist pain towards the end of a long day. I have not used my hand crimpers since I got this puppy! Check that, only on heavy gauge metal like that from a square to round, 18/20 gauge have I been forced to use my hand crimpers. These are very fast and work in both directions! Honestly these things work so good that they can over crimp at times, so keep that in mind when setting your screw making up a seam. Very happy I got these.

Never complain about crimping 22” pipe again! Works like a dream. Has bee dropped countless times and no damage whatsoever. I would recommend on pipe less than 6”. There Is a slight learning curve to it but after a dozen or so uses the motion feels natural. Young bucks on the fence about buying this I would urge you to do so, could end up saving you from some arthritis problems further down the road. Boss man joked about me wanting to live a charmed life first time he saw it. 6 months later the old b bought one himself.

Was good and well worth it at first, but only lasted 2 weeks and shaft broke! Save ur money and get the hand held ones, end up being cheap and lost out on money

A must depending what part of Hvac feels you are in. Works better on light commercial (26GA or thicker) I do residential and it can be a little too much for 30ga but does still crimp the hell out of it! Definitely a time saver. As far as quality for the most part it is a hardy part but the part that goes in impact chuck snapped early on and had to get replacement part from Amazon since then no issues for weekly use over a year.

Good stuff but my frist one last 2 years The second one is one month I’m want warranty please let me know thanks

Order 250 4" & 5" Ys and we needed them crimped because they were ordered wrong. Bought this and wow did this save a ton of time and our forearms. For the time it would take to manually crimp 1 Y, we crimped 10 Ys. Definitely worth it. Be sure to wear ear plugs with it

The chuck broke on the 2nd day be careful buying this tool , i just wasted $270 . I’ve always liked malco and never had any issues but this turbo crimper is straight garbage .

Only tried once, so far. Works fine. Don’t really like that you can’t open up to get on and off they pipe. Nor can you adjust the depth of crimp. But this one shouldn’t break like the cast aluminum Malco version.