SC01

I bought this to cover the worn out steering wheel on my 2008 Honda CRV. I previously had a “pleather” steering wheel cover from Advance Auto, and this is soooo much better! It’s genuine leather, and it looks and fits great if you follow the size chart. Tip #1: After sliding the cover over your steering wheel (with the seem in the center, at the bottom), line up all the holes with their counterpart on the other side before you begin stitching. It will look a lot neater if it’s lined up perfectly. I used a mirror to count the empty holes behind each spoke, and then marked my starting and stopping holes on both sides with a metallic Sharpie to make sure it stayed lined up well, with no wrinkles or stitching errors. Tip #2: If your steering wheel is thicker at the 10 & 2 positions, you may need to stretch the leather to avoid a gap there. Even though I ordered the correct size, based on the thicker circumference at my 10 & 2 positions, I had a gap between the leather when I got to the 10:00 position. No matter how tightly I pulled the thread, I couldn’t close the gap, so I thought it was too small. When I got to the 2:00 position, it occurred to me that maybe I could stretch the leather to fit. So I got 2 pairs of pliers and pulled both sides of the leather to stretch it a little, and then I was able to stitch it closed without a gap there. Tip #3: Rather than using “dummy” stitches in front of and behind the spokes, I tucked the leather under. As long as it’s stitched tightly on both sides of the spokes, it should stay tucked with no problem. I did tuck a small piece of double-sided tape underneath to hold it in place until I got it stitched on both sides. There are several ways you can sew the cover on. The quickest and easiest way would be the straight-stitch. I opted to cross-stitch mine, because I think it looks neater and more professional. Cross-stitching requires more time, more thread, and simultaneously using 2 needles. Therefore, I appreciated that Bellinous included 3 LONG pieces of thread, each with an attached needle, which was more than enough to get the job done. The installation took me approximately 3-1/2 hours. I’m attaching photos and a video of the finished product. I wanted to video the stitching process, but I didn’t have any way to hold the camera at those awkward angles. If Bellinous wants to send me a couple small leather samples and thread, I’d be happy to make an instructional cross-stitch video. I am very happy with the quality, fit, and final appearance of this steering wheel cover. I expect it will last a lot longer than the cheap slip-on cover I previously had, and it was actually LESS expensive! Great quality for the price!

Installed on the factory steering wheel of my 84 GM K2500. Took a bit over a hour to install. Highly impressed with initial quality. Was concerned about the fit when ordering but it was perfect. Triple digit summer heat is here so we’ll see how it holds up. But i feel it will last for years. Seems that good. Matches the factory burgundy interior perfectly.

This actually worked very well and appears to be of very good quality. They also provided two needles and more than enough thread to lace it up. The only issue is installing it and stitching it together with the included thread. Took me a while to get the hang of it and I changed my technique a couple of times before I was happy, so it ended up taking a few hours total to complete. Eventually I would put the thread through one hole on each side, compress the rim with one hand as I pulled the thread very tight with the other, then used a spring loaded clamp to keep it from loosening, like having a third hand. Repeat and repeat over and over until you’re done. Very happy with the results. It comes in several diameters and widths and colors to closely fit your steering wheel so not a one-size-fits-all approach, which would not yield good results. My car is old and the foam padding on the steering wheel was deteriorating and collapsing and beginning to rip. I first wrapped the steering wheel rim using self fusing tape to build it up and compress the original foam, which was loose and coming un-adhered in some areas. I then installed the leather cover over this tape, which worked well. I was mainly interested in function but it actually looks and feels very nice. Highly recommended, but you need time and patience to install it. If I get another one for my other car I can probably install it in an hour, but it took me at least two hours just to figure out how to do it with good results. Results are well worth the effort, feels like it’s going to last for years.

A good product for a god price. The cover feels good in the hand, and the included needle and thread were easy to use. The cover has a moderate amount of stretch to conform to grips and spokes, but will tear if pulled too hard. Try stretching by hand first. For the price, a forgiving entry into hand-stitched covers.

So I really love this steering wheel cover though it was a lot of dedicated work to stitch on. Being real leather it has a wonderful soft grip that goes fully around the handle part of the wheel rather than those bulky all in one covers that only go around partially. The leather is good quality, thick (about 1/8”) and just the right softness. It did however take me almost 2 hours to complete its installation. I have small over 50 women’s hands but had no problem pulling the threads. I did need my husbands strength to stretch the leather over the wheel at the start, but did the long job of stitching without issue. Recommendations if you get one: 1) use a sharpie and mark the Backside Only Holes. The holes on the backside are literally impossible to see otherwise and it’s critical to be able to see them for threading the needle through. Do this before starting. The holes on the top side you can see just fine. 2) watch a video for what stitch to do (I went with the baseball stitch using two needles) 3) use needle nose pliers to tighten up about the last 5 stitches you have done. Using the pliers… count back and pull the 5th back, then 4th, 3rd, etc til you get to where you are working again. Then start another 5 stitches again. (I did the baseball stitch so in my case it’s two stitches for every one). Pull those stitches til you bring the leather close together. 4) Lastly, be patient and forgiving of yourself! When I accepted that I don’t do this for a living and this is the only way I’ll get a full grip leather wheel cover I eased up on my expectations. I had to undo mistakes several times and almost gave up. But I’m thrilled with my finished albeit imperfect job! 5) and lastly lastly… Don’t forget the scented candle hahaha Seriously though…play some enjoyable tunes to stay chill! Enjoy a real leather steering wheel!

Easy to install and looks good

Installed this Belinous leather steering wheel cover on a 2010 Kia Soul, and the result exceeded my expectations. The install process took about three hours, but once I got the hang of the stitching technique, it was smooth sailing. The kit came with everything needed, and the thread held up great—no fraying or snapping. I ended up using a custom stitch pattern because the thread was pulling through the cover a little, but once I adjusted, it came out fantastic. The fit is perfect—tight, flush, and solid all the way around. No sagging or loose areas. The leather feels premium—smooth, soft, and comfortable to grip. It doesn’t get slippery even when your hands sweat, which is a big plus during long drives or hot days. I’ve had it installed for a couple of months now, and it still looks brand new with no visible wear. The cover also enhanced the appearance of the steering wheel, making it look fresher and more refined. For the price, it’s a no-brainer—and yes, I’ve already recommended it to a few friends. ⸻ ✅ Pros: • High-quality leather feel • Tight, OEM-like fit • Customizable stitch pattern • Comfortable, non-slip grip • Great appearance and durability ❌ Minor Notes: • Learning curve with stitching, but worth it • Took a few hours, so be ready to commit some time

Tis is NOT leather I got it on & it laced up (a tedious job) it came with plenty of thread and even 3 needles. the needles were great. not too pointy. just right for the job all the pre punched holes are good

Excelente funda de piel, me enviaron el producto a la medida solicitada

Worked out well, watched a few videos and went at it. It took about 2 hours and I happy with the results. I wish they made seat co hrs as well. Theose tend to be way over priced for my car.

Buena calidad cuero real

Se ve y se siente de buena calidad

The patience of the installation was well worth it. Very nice product and is holding up very nice.