WOODSKIL 9-Inch Band Saw, 3-Amp Benchtop Bandsaw, 2500 FPM Blade Speed | 3-1/2-Inch Cutting Depth, 9-Inch Cutting Width, 0-45° Cast Aluminum Table and Steel Base, Ideal Bandsaw for Woodworking

It was easy to assemble and square up the table with the blade. I cut a piece of wood to check everything out and was surprised that it cut at 90 degrees on the first attempt. I make candle holders and like to insert colored pieces of acrylic on the inside. My laser cuts extremely accurately and I was depending on this saw to cut the acrylic to fit, and the pieces had to be exact. Not only did the saw cut cleanly, but there was no problem in straight cuts, no wandering, and no variation in the cut. I did hook up a shop vac and attached a magnetic light, however. Changing the blade was fairly easy and only took me a few minutes. All in all, I would definitely recommend this saw to anyone looking for a small, quiet, and excellent band saw.

Good build quality and easy to achieve an accurate set up. Nice to have a fence and miter guide included. The miter feels a bit lightweight but does the job and a more substantial guide would add cost that, for me, isn’t needed. Dust extraction works well. Overall good value for money!

Nicely made band saw, not much different than the cheaper models. I dislike the ball race blade guides because they offer little to dampen blade vibration. These band saws can require around an hour of setup time if you need them for precision work. Good-quality blades are difficult to find online, especially those with 14 teeth per inch. The bottom wheel on the saw requires alignment to ensure the thin blades remain centered on the crown of both the upper and lower wheels. This can be done by slowly adjusting four bolts that hold the wheel shaft in its correct orientation. With a little persistence and some time, everything can be made to run correctly—good value for money and slightly better than the cheaper clones of this model.

My husband got this man toy for his birthday and loves it! He built a custom stand for it instead of paying double for one that came with a stand. Looks and works great!

Great bandsaw for the price! Adjustments didn't take too long it cuts pretty clean and straight. Cuts all my hard wood with no problem just have to go a bit slow with it. Everything is about 1/32 to 1/16 off so not to terrible. When I ripped douglas fir It was pretty bad and got about an 1/8 off not sure what that was about.. must of been the wood grain pulling the blade to one side. It's a good bandsaw and will get the job done if you are getting into wood working or need to do bandsaw projects.

I have had this a while now. Its quality is pretty good and I have used this thing a lot with no issues. Its easy to use and adjust. I am really glad I bought it and it does exactly what I needed it to do. Exceeded my expectations. Would buy again.

This bandsaw is a huge upgrade from my previous Rockwell shop bandsaw This baby set up in 20 minutes with no issues. It’s built strong and solid. I’m no professional woodworker but in testing this one it cuts straight, no blade wobble…. like my old one. Cuts a 2x4 on end with no problems. I’m very impressed with the quality and its ability to cut curves or straights. Miter gauge and fence are nice along with the ability to cut angles. A solid buy at $199.00

1)Couldn’t change speeds on saw the belt kept on slipping 2)turned on saw and it shredded top wheel tire the first time.considering sending it back not worth the trouble

all good

Muy buen producto, se hacen buenos trabajos

Es muy practica y me sustituye muy bien a la caladora. La utilice para recortar madera en forma de corrientes de agua para un diseño de piso de mi estudio

Value for money wise, this is an excellent piece of equipment, but a couple of things could be better. The fence is difficult to position accurately due to the locking mechanism, which doesn't slide easily against the table edge and tends to move as the lock is engaged. A more concerning problem, though, is that the blade guard is impossible to open. The user instructions just say "pull open", but I've tried pulling, squeezing, lifting... and it doesn't budge. I googled it and others seem to have encountered the same issue. This doesn't affect the operation of the saw for now, but it will become a major problem when the blade eventually has to be changed. Otherwise, I'm very happy with the purchase.

A ver, es una maquinita para trabajos ligeros, casi para hobby. Pero la uso mucho en el taller. Y por el precio, te la recomiendo. Está limitada en capacidad de corte, no es para piezas demasiado anchas ni gruesas. Pero para detalles es de lo más útil.