GP-Ultimate 15W-Thermal Pad 90x50x1.0mm (2pcs). Excellent Heat Conduction, Ideal Gap Filler. Easy Installation.

I've had a great experience using these thermal pads for my Samsung 990 Pro SSDs. I used them with the motherboard SSD heatsinks and there is a stark difference in SSD temps before and after. Before it would hit 80°C under heavy loads and 40°C with regular use. Now it stays at 40°C during regular use but struggles to hit even 50°C under heavy use like benchmarking. The pads are solid, retain their shape well, and are very easy to work with. Use a fine tip sharpie to mark where to cut on the plastic film, then cut with a ruler and X-ACTO knife for perfect results. They aren't exactly cheap and it cost me about $7 in material per SSD, but for the performance it is well worth it, even more so if it is for a GPU. Thermal pads are not advisable for CPUs, contrary to what they show in the listing photos. They will always underperform compared to paste, and they cost more as well. It is worth mentioning that these pads are a bit less pliable. They don't compress as much as the factory pads did, but that was easily fixed by smushing them down a bit before installation.

These pads are awesome! I put them on my RTX 3090 FE and the two pads are the perfect amount to cover the entire card. I just used a video as a template of how to cut the pads and where to place them and it worked absolutely perfectly. Now the GPU core and VRAM stay around 75 degrees at full load (Unigen Heaven) with about 88 degrees on the hot spot. That's with the fans relatively slow too. Definitely better than I was expecting!

Quality thermal pads for SSD housings. I purchased 3 sizes to fit multiple contingencies

Used to fix cooling issues on my Asus X670E-I motherboard, specifically for the Chipset that handlea the NVMe drives. Temperatures dropped from 90 to 60 degrees Celsius.

Worked perfect to repad an aging PS3

Good replacement, keeping memore

After searching the web/YouTube for the correct thickness of pads. Found the thickness I needed for both front and back of GPU. I have the latest version of Nvidia RTX 3080 Founders Edition. Which require different thickness than the original 3080 Fe. For the back, I used the 3.0mm thickness Gelid Extremes. For the front, I used 1.5mm thickness Gelid Ultimates. Under load, VRAM temp went from 96 degrees Celsius down to ~70 degrees Celsius. I redid thermal paste. However, I did recall what I had prior to modification. I used Noctua H2 thermal paste. Under load getting ~ 59 degrees Celsius for GPU temp. The temps are with 65% fan speed for GPU. When cutting pads for both front and back. Don’t be concerned with cutting pads to completely over cover the chips. Try to be as close as possible when cutting and covering the chips. Reason being is because you may risk thermal pad overlap sections of the PCB. That would prevent you from closing the GPU enclosure properly. Causing not a good contact with die and heatsink. Then you’d have to open the GPU again. And trim the pads. To get better and straight cuts of your pads. Get a clean sharp utility knife or surgical type of knife with a ruler. I bought a arts and crafts set that came with a couple of knives, cutting mat, and metal ruler. Helped lots in comparison to using scissors.

Great quality thermal pads. Used this for my Thermalright SSD heatsink/fan. Stock pads were thin (1mm) and had poor thermal conductivity. Nice upgrade in performance. Just cut them to size using sharp razor blade and straight edge. Peel and stick.

Great pads, mem temps noticably dropped to mid 80s,only issue is, they are not so soft as gelid extreme but worth that money

Me ha sorprendido para bien estos thermal pads de 2 y 3mm para mi zotac amp holo 3080, la última vez lo cambié hace dos años pero esta vez decidí poner estos de gelid ultimate, dejo imagen de temperaturas de antes y después

Dopo aver cercato in lungo e in largo un pad termico che garantisse performance di raffreddamento ad un prezzo adeguato ho scelto questo per raffreddare processore e chipset di un pc industriale fanless. La scelta è stata azzeccata. Il materiale è di ottima qualità e la temperatura si è abbassata a valori consoni. Lo consiglio

Not to be used (1mm) on a CPU cooler. Temperatures are horrible (best to try 0.5mm or 0.2 if it exists). For VRAM modules I guess it will work but I haven't used it for that so I can't be more explicit.

Les meilleurs pads thermiques que j'ai pu avoir jusqu'à présent, ils n'ont pas de fuites d'huile comme avaient les originaux de ma rtx 3070 gigabyte à haute température. Ils sont plutôt durs et j'ai pu en placer entre la backplate de ma 3070 gaming oc edition (il faut du 3mm et entre le dissipateur et les vrm, là il faut du 0,5mm ou du 1mm max). Les températures ont beaucoup chuté grâce à ces pads thermiques avec une meilleure conductivité thermique que les thermal grizzly pour le même prix !