WATTS BRASS & TUBULAR Whole House Hot Water Recirculating Pump

I wanted to wait a while before reviewing this device to gauge it effectiveness. It's been installed about a month now. I have a 2000 square foot home sitting on a slab, so my water lines (Pex) are in the attic. Although it does not get terribly cold in Southern California during the Winter, it used to take upwards of 30 seconds before the water would get warm. That was a lot of perfectly good water going down the drain. After installing this device, it now takes only 5-7 seconds before the water starts to warm up. Interestingly, the closer the faucet you are opening is to the valve, the sooner your water will become warm/hot, so I find that the sink next to the one with the valve (in our master bathroom) gets the water warm-to-hot within just a few seconds. It's important to tell you that the water will not be piping hot and waiting for you right when you turn on the faucet, but the amount of time, money & water you will save is still worth it. The pump attaches to the top of your water heater and is VERY quiet. After installation, I had to touch it to make sure it was running. Although I have mine set to "On" 24 hours a day, I appreciate the timed feature that allows you to turn it on and off at certain times of the day. It runs on 110 volts, so you may need to buy an extension cord to plug it into an outlet in your home or garage if it's not close to an outlet. As mentioned elsewhere, check the WATTS website before buying as apparently this device will not work with all water heaters. I failed to do this, but I was lucky. Also, it will not work with a tankless heater so do not try it! As far as installation goes, I'm fairly handy around the house, but plumbing is not my strong suit and I scoffed at the notion that I could install this in one hour. However, it took just a little over one hour (as advertised) to install with the only hiccup being a crowded space under the sink where the valve was installed, causing me to get creative with the hose routing and placement. Don't feel like you have to mount the valve to the wall. Mine is working just fine without mounting. I didn't even need to bring out my plumber's tape/pipe dope because everything sealed up great the first time. As an aside, while you have your water heater dismantled, go ahead and drain it. It's probably been a while. My wife was thrilled when I (finally) installed this device after maybe 3 years of her asking. She heartily recommends it and so do I.

We have been in this house for 6 years and have been frustrated with how long it takes to get the hot water from the tank to the bathroom. We were always washing hands and brushing teeth with very cold water, and running the tub for a long time before any hot water got there. Finally I found out about this product. I wasn’t too enthusiastic about using the cold line as a return. I thought that would result in warm water when we wanted cold. Also I replaced my tank a couple of years ago and the new tank has a heat trap so I read that it would be a problem with the proper operation of this unit. But my research found that worst case was that I could remove the heat trap on the hot side and replace it with a plain nipple so I decided to purchase the unit and try it out. Installation was fairly straight forward although I had to remove a section of copper pipe and solder it back together, but that was a minor task for me. The hardest part of the installation was tightening the fitting onto the outlet side. There is nothing on the pump housing designed to put a wrench on to stop the pump from turning. I had to put a crescent wrench on the housing where it bolts together which had me a bit concerned about cracking the housing. It did turn out ok though. I got it all installed and fired it up. It is quiet, slight hum, but it is located in an unfinished b a segment (cellar really) so unless I go down there I can’t hear it. The great part is that the heat trap has not interfered with the operation at all. I get hot water at the bathroom sink and tub almost immediately. This makes me very happy every time I turn on the tap. I don’t use the timer at all. I installed a smart outlet linked to a phone app so I can shut off the pump whenever I need to (like if we are going away) but so far the pump runs 24/7 since we are home most of the time, and we want hot water at the bathroom even in the middle of the night. One bonus is that I also get hot water sooner at the kitchen which is on a different branch but it tees off about 10 feet after the tank, so its already about ⅓ of the way there. I may upgrade with an additional valve under the kitchen sink but I am thinking that I will be ok with it the way it is for now. It has been about 2 weeks since install and I am very happy with this pump system.

After years of waiting for water to reach the far areas of my house, I had finally had enough. This pump exceeded my expectations and works flawlessly. It sat on my counter for a few weeks until I finally decided to install it. Installation time was less than 30 min. It took me longer to get the junk out from beneath the far sink than it did to install. The instructions are straight forward and easy to understand. I did the under the sink valve first. They supply you with all the right hoses and connections. I did have to get long hoses, but that is not the fault of the mfg. My supply pipes are further apart. I bought longer hoses and everything was golden. Installing the pump was beyond easy. Yes I did have to buy the correct CPVC fittings with 3/4" threads to connect to the pump. Less than a dollar at the local hardware. Off the discharge pump I went with a flexible hose that connected to my system. You will have to buy a few extra pvc fittings if you need to make it work with your water heater system. It took less than 30 min to install in total and I plugged it in. I could tell it was working, but the pump is extremely quiet. We set the mode to timer, because we want it on from early morning to around 11 pm at night then the timer shuts off the pump. You will still have hot water, but just not as fast as when the pump is working. Even if you let it run all the time, it would cost around $20 a year, tops, but the timer is a nice feature. So far I am extremely happy with the product and it has hot water at our furthest sink within 5 seconds. Don't hesitate to buy this product.

The pump and temperature bypass valve have been installed for approximately 1 week and so far so good. I had a concern that the cold water line would be too warm with the hot water bypassing into it to maintain hot water lime temp but not too bad. The cold water from the faucet at the bypass valve sink is at about room temperature. It is a trade off to have room temp cold water instead of icy cold-cold water at the tap since I didn't have to plumb in a return line. I did install a downstream ball valve so the HWH & pump can be isolated if anything requires service in the future The pump has been running 24/7 as I have yet to program the timer so not sure how that is going to work.

I can honestly say this is probably the most cost effective way of getting hot water to far places in a home, Our home 12 years old is roughly 3000 sq ft 2 story with 4 full baths with the master being at the most furthest point of the home upstairs roughly 100+ feet away from the hot water tank in the garage between the master bath sinks, jetted tub and shower I would have to wait almost 4 minutes of water running before it got warm then cold. The water lines used throughout the home are PEX non metallic plumbing. The pump and sensor unit are very easy to install on your own with a bit of common sense and took me about 40 minutes to install. I let the pump do it's thing for about 30 minutes went up to the 2nd sink in the master bath, which is the last and furthest in the home only 3 feet further than the 2nd sink, within approx 3 secs the water was warm to the touch followed by hotter water very shortly thereafter. I had my wife verify this later that evening, we would usually waste a bunch of water filling up the jetted tub or turning on the shower waiting on hot water, again within seconds the water was warm then hot! I was very amazed as I was getting prepared to drop a few thousand $$$ to have a Tankless installed just for the upstairs master bath I am very pleased with this system. Now I have seen where some people are concerned about cost to run this etc. first it waste no water so right there whatever the cost should be outweighed in water savings. Second I have seen people mock those about putting this on a smart timer since it already comes with a built in timer, what those doing the mocking are not realizing is that if the power goes out then the built in timer does not keep its correct time once power is restored, Yes I'm sure for many this is probably a very rare thing, but I can tell u you here in Northern CA the power especially in the summer is 50/50 at best! So yes I would highly suggest the use of a smart plug for one of these, I already have dozens of smart plugs/lights & switches in use at my home so I did not need to purchase one but they can be purchased for less than $25 I recommend Tp-link by Kasa! The other nice thing about the smart plug especially if it has the energy monitoring option (Not all do get one with the monitoring) is that you can get a real time look at what the power consumption is daily, weekly and yearly to kind of give you a idea of the Electric use which is not bad. The pump averages right around 22 watts +/- while running the company states is should be less than a nickle a day or so to run 24 hours. I may set up a schedule or Alexa routine but currently I have not having 48 345 watt solar panels and Battery I am not to concerned about 22 watts running. On to the gas usage, given we have a large home along with large heated pool/Jacuzzi and outdoor gas fireplace etc. we have a very large diameter gas line with a smart meter. I can always here the meter gurgling so to speak when any of the large items are being uses including the hot water tank, to date after checking numerous times I have yet to hear the gas meter or the actual hot water tank firing constantly, not saying it does not fire up once enough coldwater gets pushed back into it I am just not hearing it like a normal tank being heated up! So again I do not believe that the complaint of this using mass amount of utility to use 24/7 again as compared to dupping 100s of gallons a day down the drain I fully believe at best it is a gain in savings at worse it is a break even! I did have to purchase a second sensor kit to place in the kitchen downstairs as our home has a branched Hot water line since doing so even our kitchen sink water is now warm to hot within seconds. I have yet to experience the so called major bleedback into the cold water line that some have stated happens that when they turn on the cold water it is warm to hot for a brief moment, either way even if I did it is still worth every penny for this setup!