(3 Pack) Designed for Garmin GPSMAP 62 62s 62st 62sc 62stc 64 64s 64st 64sc 64x 64sx 64csx 65 65s Tempered Glass Screen Protector, Anti Scratch, Bubble Free

Easy to apply, I try to put protective screens on all my GPSr's. This has already been dropped a couple of times, and I know the screen underneath is in good shape.Fit is perfect for my model, and I have no issues seeing the screen, regardless of the weather.

They work great. I'm hard on equipment and have had to send units in for screen repairs. They're just never quite right after that. Twice I have struck the screen and thought for the screen protector and unit screen would be cracked. The protector cracked but did its job. Glad there is more than one to a pack. Easy to install and pretty easy to remove. They have been very resistant to scratching.

These were a good fit on my Garmin GPSMAP 65s. Not excessively wide like a few reviews mention. I wonder if all Garmin screens on this series vary a bit with the amount of chamfer. Mine could stand to be maybe a half mm smaller split between the two sides. Due to the angled sides of the screen even if it was a perfect fit, the edge of the glass protector is a bit vulnerable to chips. I ended up adding a Tusita silicone cover and that completely shields the edges of the protector anyway. The glass is crystal clear and I don't even notice it's there. It went down with not a bubble to be seen. No instructions specific to Garmin but I used one of the supplied tape tabs on each side to handle the protector after peeling the backing. Do a couple dry runs so you can eyeball it and set it perfectly. I could have done better centering it top to bottom but it set down so nicely that I didn't want to risk peeling it up and getting dust under it. Side to side placement is more important, no room for error. The Garmin screen is plastic so you really need something like this.

Works fine

In my opinion, these tempered glass shields are not a good fit for the Garmin GPSMAP 65s. Yes, they have the general design concept following the perimeter around the 65s's display though the edge of the shield will generally be 3-4 millimeters smaller than the display in size. From left to right, your screen will be covered (except for the beveled edge). From top to bottom, your screen will remain unprotected beyond the edges of the Shield. The area of the display that is most important and contains the data you'll be using, is protected.*Supershieldz - Install Video*The install video was developed for a thin iPhone device, not for the Garmin 65s which is much thicker. Attempting the suggested "hinge method," with tabs designed for a much smaller device, will screw things up. I removed and tossed the first of three shields provided due to the failure to provide accurate information for the Garmin 65s.I installed the second glass cover free-handed, mimicking the other instructions and without use of the hinge method. It looks good and will protect most of the screen, but this isn't good enough for a tool that is supposed to protect the device's full display. A chip and crack in the unprotected area may end up spreading damage across the remainder of the screen.

I have put these on all the GPS units for our search team, good stuff.

This is a survival tool for me. Should I ever get lost in the deep woods I have tested it under conditions of duress just see how reliable and useful it is. Its graphic aren’t great more like an old cell phone with large pixels. Other than that it is a great way to stack your own position on the globe and can be easily used with a supply of double AA batteries which I suggest you always carry with you in your pack.

Downgrading to one star…didn’t last a day. Cover shattered starting at the edge on the 65. Being too wide as commented below was the cause. There was no bars bang, sir or anything. A slight bump from the side shattered it.The Garmins are not well suited for protectors but need them most. I need to find a non glass scratch protector. Not the best but better than the glass protectors.Original Post.It peeled off the 64 as I suspected it would.The size is generic 65/64 size and not a perfect fit for either. Too long for my Garmin 64s, which causes incomplete adhesion at the top so I don’t expect it to stay on for very long at all. It is too short for the 65s, but covers the actual screen area, but not the entire face.It seems like the width is cutting it too close to perfect or maybe even a tad bit too wide, so I’m not sure the screen will stay on because now there’s an edge that extends past the bevel of the face. This is creating a catch area where anything sliding along the face bevel of the GPS could cause the protective screen to lift up allowing dust or separation.