Safety Goggles, GoggleGear 500 Series, Scotchgard Anti-Fog Clear Lens

I have a 3M 7500 series respirator. During a recent project using RMR 86 and 141 to clean and disinfect an area that took some water damage, I needed goggles that would protect my eyes from the mist and fumes while also using a respirator. Very tight space, almost no ventilation. Unlike a lot of goggles, these are designed to fit well when used with this respirator (maybe others too). They're low profile, have good peripheral vision, lightweight, seal completely without impacting the fit of the respirator. They're also comfortable to wear for extended periods and have ANSI Z87.1-2015 impact resistance. No issues with fogging. I was working indoors in a temp controlled environment. Could be that because of this, the conditions that result in fogging were limited. Perhaps most importantly, they're a 3M product. Among other things, 3M is a global leader for safety products and can trusted, sometimes with your life, to perform to spec and as advertised. Tip: I'd suggest cleaning them after use. Dish soap and a water rinse worked well. Doing so will help maximize service life, leave them ready for the next project. Highly recommended. Great price too. I consider these a 'just buy it' product.

I think these are my favorite safety glasses overall. They fit good with a 3M half mask, extremely clear optically, curvature doesn't give much distortion if any of that I can tell of, and very comfortable for extended periods. I can still get them to fog if it's hot, but I've never had glasses that don't when it's hot and I have a welding helmet on. I've tried a few different brands because I had a speck of metal bounce off the nose piece of my respirator and flew into my eye behind a pair of regular safety glasses. I knew at that moment I needed to have something better like goggles. Im not a big fan of face shields especially since I often have a welding helmet on. If you have an easy access grind mode on your helmet maybe that works, but I still prefer to flip my hood up for better visibility. These fit really well under a helmet since they are pretty low profile.

I wish the lens was more scratch resistant. But they are not uncomfortable. I bought several pair. I keep one hanging on my lawn mower, and a couple in my work truck. I tore the top of the package bag they come in so i can put them back into the package and hang them up when im done using them so they arent thrown around getting scratched up. If im really sweaty, they can start to fog a little.

Good quality, like everything 3M makes. They are not completely fog free, but they're better than most. These goggles are intended to work with 3M half-mask style respirators.

Comfortable, Clear Goggles That Don’t Fog Up These 3M GoggleGear 500 Series goggles are an easy 5‑star win for eye protection. The low‑profile design sits comfortably with a good seal, and the strap keeps them secure without digging into your head. The lens stays clear and resists fogging very well, even when you’re working hard or wearing a mask. They also fit nicely under a hard hat or over most prescription glasses. For shop, jobsite, or DIY use, they’ve become my go‑to safety goggles.

I bought these for woodworking and I must have read the description wrong as there is no venting in these goggles. I was excited when I put these on because they had such a great fit and sealed well. What I didn't notice was the lack of ventilation holes or slots. While I was doing some light work I noticed my vision seemed as though I was looking through water. I took them off and cleaned them well and put them back on and tried again only to have the same thing happen except worse. I do have to say they did not fog up, the moisture just gets on the interior lens and starts to run down like a waterfall, but no fogging. I returned this product for one that had ventilation. These would be good for someone that is not doing too much work and create moisture inside the goggles. They had all the ratings that I was looking for and were easy to adjust.

I had been looking at many different types of goggles in order to protect myself as an emergency room nurse dealing with COVID patients on a daily basis, i ordered a these 3m goggles and another different set. These are by far the best goggles i've tried. They can be adjusted to a very comfortable fit, are lightweight and do not obstruct my vision when I need to start IV's or doing invasive procedures during patient care. The seal feels very safe, and they rarely fog up, which I attribute to getting a proper angle between goggles and the n-95. I place these on my head and slide them on and off with great ease in a matter of seconds. They have become an essential part of my safety gear in the ER.

Perfect fit excellent clear vision. Comfortable fit

A mi me parece una buena opción, los uso promedio 5 horas seguidas y no se empañaron, son cómodos y sobre todo ligeros, hacen buen ajuste con las mascarillas. Este es el mejor modelo que se ajusto a mi cara. Definitivamente lo volvería a comprar, lo malo ya no están disponibles.

I love these! I wish I'd bought them sooner, always working in attics getting insulation in my eyes, cutting drywall getting dust in my eyes, sawdust... You name it. I always hated wearing safety glasses cuz once I started to sweat they'd fog up. I've worn masks and stuff while sweating wearing these and got absolutely no fog now three times using for multiple hours. Get them

The item, valued at 3000, did not include a protective cover, a feature typically provided even with shields costing 500 rupees. Consequently, it offers poor value for money and exhibits fogging.

Perfect seal, low profile can be worn with a baseball cap. Extremely clear, hardly any visible reflections. All day comfort. However they do not pair well with 3M 6000 series medium size half face respirator mask for this reason I ordered a pair of Dewalt DPG82-11 which although huge (can’t wear a baseball cap) and not nearly as comfortable fit perfectly with 3M 6000 half face respirator.

Estos googles están super, compra ya