18" to 28" Long Adjustable Gas Lift Cylinder Tube for Bar Stool Drafting Chair Replacement Parts,Heavy Duty Hydraulic Pneumatic Cylinder Shock Piston (10" Lift Stroke)

Works great. Much better than what chair came with. At 320 lbs I can kill a chair!

Great quality, easy installation, great product, exact fit, works as intended.

An older task chair was slowly sinking over the course of each day necessitating constant adjustments. This replacement was perfect and made the chair usable again. It took some muscle to remove the old one (YouTube videos were helpful) but once removed the install was easy.

Miscalculated the height...very stable and high quality material though.

Replaced a failed gas cylinder on a random drafting stool I bought from a local office supply company with this product. The cylinder fit perfectly and the chaiir is a little higher (which is exactly what I was looking for).Note - if you have a foot rest with a rubber gasket, use a little dish soap to lubricate it and get it where you want it. It will be too slippery at first but once the soap dries out it will be perfect.Suggest you verify the sizes and go. I like the chrome vs. black finish as well.

I've been suffering with a slowly failing cylinder for my draft chair, which is my home office work chair.. My chair would slowly loose altitude at random and most inconvenient times. Usually while I was talking on a zoom call.. and I would be distracted by my video image slowly descending, then would have to awkwardly half standup while I hit the release level to raise altitude again.watch videos on youtube on how to remove your old cylinder, there are a couple of tricks that make it a lot easier.. I had a failed attempt after I tried to wing it on what made sense to me, then took 3 months until I took another stab at it.I can't attest for longevity of product as I've only had it installed for about a week.. but so far this replacement holds my 200+ pounds solid. No slips, I don't constantly have to re-adjust, it's just working!

If you haven't changed one of these before, search the web for a video. I bought this for a counter height bar stool. The old cylinder would drift down and wouldn't hold the seat elevated. The new tall cylinder I'm reviewing is the right height.Taking the old one off:Removing the part that attaches to the seat involved twisting the wheeled base while holding the chair-back stationary. It came free fairly easily. That left the rest of the cylinder stubbing out of the still-attached wheel section. That didn't come apart so easy. For thirty minutes I beat it with a mallet, twisted it with a pipe wrench, and nothing. I then set the wheel base upside down loosely in a steel vise. I used a heat gun to circle around the base collar holding the cylinder for about ten minutes. (A hand held torch would have also worked, but the heat gun didn't risk discoloring the steel or melting any plastic.) Once it was too hot to touch I gave it a hard whack with the mallet and it came free at once.Putting the new one on: (easy peesy)I slipped the big end in the base as far as it would go. It went right in about three fourths of the way. I then set the chair on the upward portion of the cylinder. This went easy. The only thing left was to sit in the chair to push the bottom of the cylinder into the wheel base. I had already oiled it around the base and with my big butt sitting in the chair and wiggling, the cylinder slid all the way home.The garage sale stool now works as well as it did, or perhaps better than it did, new. The price of this cylinder was all it took to avoid buying a new stool. I couldn't be happier.

Lo compré para un bar toors y que do perfecto. Muy bueno.

Alles perfekt !!!!

Had to replace lifts that would not work. These were perfect and work great.

Der Gasliftzylinder stimmt mit der Produktbeschreibung überein. Brauchte meinen Chefsessel daher nicht Entsorgen 👌

Worked perfectly in my Jysk VEJERS stool. Took some effort to get the old item out of the chair, but once it was out, the new one fit perfectly and performed better than the original. I thought I was going to have to throw away a perfectly good quality stool when it wouldn't stay in the up position, but all it needed was this part.

Working just fine so far. One of the few places I could find a bar height gas lift. Most of them on offer here and elsewhere are for shorter desk chairs.