Haoge LH-X54W Square Metal Lens Hood Shade with 49mm Adapter Ring for Fujifilm X100VI Fuji X-100VI Camera Silver

Bought for new X100 vI - perfect fit. There is a small rubber seal (and a spare included) behind the cap so you can rotate it to align and then keep it tight. You can see the slight corner of the shade in the OVF but not in the EVF. Well worth price for keeping my protective filter pristine! Silver version a perfect match for my body (the cameras!)

Love this lens hood. Looks great and provides lots of extra protection. My only issue is that after a few times of attaching and detaching the hood, it no longer tightens at the correct level, leaving it very slightly tilted. It’s so minor but still irritated me. I found a fix though - I attached a small elastic band around where you screw on the hood and it gave just enough extra resistance to tighten at the perfect level every time - definitely recommend doing that if it’s annoying you too

Looks nice and matches the silver colour very well so that it looks very natural, like an official Fuji product. But like others say, when you fully tighten the hood it is not straight and therefore you need to loosen it a bit to get it level. Sometimes you can then accidentally knock it and move it to an angle slightly. Not a bit deal but they should have manufactured this out during testing. Also it's a tad expensive what it is, about a tenner less would have been right. However no vignetting etc and pretty easy to fit. Don't throw away the spare red elastic band as this is a spare in case you break the one that comes with it ( think it enables it to thread properly when you screw it on).

You need lens cap that compatible to this hood from haoge, original fujifilm cap wont fit. Seller should sell them together rather than separately. This is a good hood, and the cap also good

This lovely metal lens hood is a great addition to X100v it looks great.. on mine I had already installed a weather resistant genuine fujifilm kit.. this fits perfect with it by just adjusting the adapter rings.. I know some reviewers have said they can't get it square on but when its on you just turn it slightly to get it in line no problem ...Also the original FujiFilm lens cap fits the lens hood .. it look lovely glad I ordered it ..

Well made lens hood that is easy to fit and use. Some have remarked that - because it's a screw fit - it does not sit straight when fully tightened. To an extent this is true but you can always achieve a straight fit by varying how 'tight' you screw it on. I have also had no issues fitting a UV filter. The downside is that you really cannot use the metal Fuji lens cap (despite advertising that it fits). It does not fit with the hood in place - and if you remove the hood it doesn't securely fit the adaptor ring either.. Why not just supply a purpose made rubber end cap ?? You either have to remove the whole thing to fit the Fuji cap or just live without a lens cap.

I’m giving this a 5* review for the product as it is a beautiful and functional accessory for the X100V. Unfortunately the first hood arrived with both rubber rings missing in a box that had obviously been opened raided and returned to Amazon. I’ve returned that one, which will no doubt be sent out to the next unlucky buyer (possibly you). The hood is a two piece affair with a filter adapter that screws on to the X100 lens (remember to remove the original screw on bit of trim). The adapter has a milled gnarled outer ring that looks even better than the the V’s focus ring. The hood part screws on to the filter adapter, with the red rubber ring between them. The rubber ring is essential because it’s the part that allows the hood to set horizontal. A spare rubber ring is also included. I still like the original round lens hood (pictured), but this is a great look too!

I ordered this square hood to aid in protecting my Fujifilm X100V. The arrival was quick (as expected from Amazon Prime). I fitted the hood to my camera there are no instructions and it's self-explanatory to an extent) you just unscrew pre-existing ring from the end of the lens and then screw the included adapter and add a filter if you want (I added a BW XS-Pro 40 Digital filter). Everything screws into place - HOWEVER - it does not align no matter how much you try it will not align and is vertical instead of horizontal. I tried with a filter on and off and still no joy. It ruins the aesthetic look of an otherwise beautiful camera. One option would be to leave it loose and then position it. The problem is that it then rattles and is no longer weatherproof. This is a bad buy and I do not recommend you waste your time with it unless you don't care how your camera looks. I wish I had read further down at other reviews that say the same thing. Not fit for purpose.

Fits well and straight to my Fujifilm x100vi, what i love is my black mist filter or any filter i attach to it stays hidden under silver color as it screws filters inward. So it doesnt shows black color filter frame and branding etc. Also original Fujifilm cover fits and doesn't fall off easily. Gave 4 star only cause the silver color differ slightly from the camera color.

Tutto perfetto come da descrizione. Si abbina perfettamente alla versione VI

Queda genial e incluye una banda elástica entre juntas para que aisle totalmente , y otra de recambio. Estoy muy contento con este parasol.

Très bonne qualité, s’adapte parfaitement, je recommande

Die Gegenlichtblende sieht super aus und ist schön verarbeitet. Dass sich die Blende nicht genau passend festschrauben lässt, wie hier viele schreiben, ist ein Problem, das ich ebenso hatte. Aber Aufgeben wollte ich nicht, da ich vom Design überzeugt war. Um meine Fuji vor dem kräftigen Drehen der Blende zu schützen, habe ich entgegen der Anleitung (erst den Ring, danach die Blende drauf zu drehen) den Ring und Blende von der Kamera zunächst wieder abgeschraubt. Dann habe ich den Ring und die Blende wieder zusammengeschraubt. Der Trick ist jetzt das festdrehen mit (heftigen) Kraftaufwand so fest es geht aufeinander zu schrauben. Ich dachte mir, wenn dann geht das Produkt kaputt und immerhin nicht meine Kamera. Meine Finger haben danach ziemlich weh getan, aber es hat sich gelohnt. Ich wusste ungefähr wie viel fehlt, damit die Blende später auf die Kamera passt und so näherte ich mich Millimeter für Millimeter an. Zwischendurch lohnt es sich die Blende samt Ring zum Testen auf die Kamera zu drehen, damit man sieht was noch fehlt. Ich war am Ende sogar etwas übers Ziel hinaus geschossen und musste wieder etwas aufdrehen. Es ist wirklich hart, dass es nicht anders geht aber bevor ihr die Blende zurückschickt, versucht das. Es lohnt sich und nichts ist kaputt gegangen, daher auch keinen Stern Abzug 🙏🏻