King&Charles Cabinet Hardware Jig & Automatic Center Punch Set. | Avoid Jitter Caused by Direct Drilling. Cabinet Handle Jig, Use for Handles and Pulls on Drawers and Doors

We had our bathroom cabinets painted recently. They originally did not have any handles installed, so nothing to remove and replace. Once I set this up, it took the guesswork out of marking and drilling perfectly aligned holes for handles to be installed. Great quality for the price and so simple to use. Highly recommended!

Very useful to installing cabinet handles. This product is well made, and once you figure out how to use it (not complicated) it works well and simplifies the work. Well built product. Good price for the unit, and very good concept. Allows for consistent and accurate handle placements.

For the DIYer, this is a great jig for precisely locating your cabinet hardware with consistency. There are other more expensive versions out there, but they cost a lot more. This one worked as expected. It’s simple to set up. From the time I opened the box, it took less than 10 minutes to set it up for my first project. Probably would have been half that time if I had actually bothered to read the instructions. Once the jig is set up, marking the holes with the supplied spring-loaded punch is quick. You do need to take a little care with the punch as you can get it at an angle in the guide hole if you’re not careful. I like the method of only using the jig to locate the holes for the punch. The other versions out there show you drilling through the jig bushing. Trying to hold the jig, the cabinet door/drawer and the drill would be tricky. I pre-drilled the 11/64” holes with a 3/32” bit to ensure it stayed aligned with the punch marks. My first project was complete in less than 30 minutes from opening the box. I would definitely recommend this for the DIYer. The jig may not hold up long for the professional installer doing hundreds of pulls each year. I dinged this product 1 star because of the instructions. The product is made in China and the instructions are translated from Chinese (assumption). I see this all the time. The translators, probably software, do a poor job with the English language. The front cover of the instruction pamphlet is titled “Handle Cabinet Haroware Jig”. The next line says “Metric and Imoerial Double Scale”. Then key features are listed that include “Porous Measurement” and “Protable”. The back of the pamphlet says “How to Intall”. There are multiple grammar errors within the instructions as well. These are easily corrected if reviewed by someone that has English as the first language.

A great tool to make your cabinet handle installation easy. The jig is well made and helps make marking holes for drilling easy and accurately.

I used this to install 14 handles (only 62 to go). I used this on 4 different sizes of drawers. It worked brilliantly. It made installation go so much faster. The included punch was much better than trying to hold everything in place AND drilling. It will be priceless when doing cabinet hardware. Although it is not made of heavy duty materials it will be sufficient for home diy needs. The thumb screws are easy to loosen and tighten, yet hold once tightened down.

Amazing product. I did 18 cabinet and 8 drawer knobs in under an hour because of this tool. So easy to set up and use. I highly recommend getting this and then put it where you can find it for future use.

The tool works well, the material is very fragile and it moves around a lot during work, the horizontal clamp is not very secure and you still need a level to use it at the same time.

I wasn't sure what to expect for a $10 product, but I am super happy with the purchase. I used some specialty pulls with base plates, so alignment was critical to the look. The jig was really easy to use and adjust the set up to fit my hardware. It helped get the drill holes lined up perfectly for my project the first time.

Worked great and saved a ton of time having this reversible jig to install new handles.

did what it said it would doo

Intelligent et ingénieux facile a utiliser

I used this to do my shop cabinet door and drawer handles.....it all worked out well.....but I will say it's not the sturdiest jig. But with a clamp and a steady hand you can get good results. Personally I used the steel lined guide holes to drill directly with my bit without using the marking tool. I'm sure you could do either but just make sure you have a good hold on it and use clamps as the plastic can flex. I would guess on spread out handles using the full ruler it would be dicey without clamps. Secondly I didn't reply on the rulers simply because I use always measure with a dead accurate quality ruler. But I found the easiest way to determine your handle holes is to attach them to the jig and tighten down or lay beside the holes and center it by eye. This worked for me but double check everything prior to drilling.

Would definitely recommend. Super easy to use.