12" X 78" Carbon Fiber Decal 3D Wrap Vinyl Film Sheet Air-Release Adhesive Roll for Auto Car Truck Art Deo (BBlack)

I used this wrap to re-finish a Yakima roof rack fairing that has been out in the elements for 14 years. It sealed perfectly with no bubbles and is holding up really well in the elements after 2 months, including a ton of rain, light snow, and ice after the rain has frozen over night.I also wrapped a pen with it for giggles and that worked well, too.***UPDATE: 4/25/2016 - After a year and a half the Yakima fairing that I wrapped still looks clean and new. The vinyl does not fade, discolor, or lose its seal, even around the edges on the back side where it is tucked under and wrapped around. I'm considering doing the hood of my car with this, as well. I'll post another update if I do.

I used this vinyl to cover some of the plastic trim on the interior of my car (near the rocker panel where shoe scuffs are a battle). The carbon weave looks phenomenal and the product felt durable. I just bought the 30“ x 60“ Moyishi carbon vinyl to cover the back of my car seats...at least until a real carbon seat back is available for my Tesla Model 3. I have a feeling that most people who write a negative review regarding the product are not using a heat gun or haven’t installed vinyl before.

Excelente!

SERIOUSLY BEAUTIFUL!!! When light bounces off of it, it's just amazing. I've used it for so many things and have so much left over still! (I bought ithis about a year ago) my favorite is my wrapped longboard (picture connected) the carbon fiber wrap is pretty strong and is easy to clean when it gets dirty. It's easy to wrap with this stuff! I got hardly no bubbles! I recommend and have fun!

Bought it to do the center dash on my dodge ram. Did not like the wood grain anymore. Its not nearly as sticky as i was hoping it to be. It does look nice and pretty easy to work with. just wish it was a little stickier to work around small areas. Worked great on back of my laptop.

Love it. Great for the price. I wrapped my Tesla interior with it and it came out really nice. It’s not too thick which makes it easy to work with. The adhesive is strong enough. There were times I peeled it off and restick it and it worked. Just make sure you clean the surface with alcohol before sticking it. I love it!

I've worked with different wraps over the years, mostly with covering R/C planes. So I figured this has to be pretty much the same process. I wanted to cover the radio faceplate in my GT/CS. For some reason Ford covers the upper I/P in carbon fiber but leaves the lower that crappy silver. Anyway, I got this, broke out my xacto, heat gun and hot gloves. The covering went on pretty much as expected and looked really good! THAT DIDN'T LAST! Anywhere that there was a compound curve this stuff let go. I completely removed all my hard work and recovered the piece allowing a little extra in those areas. YOU GUESSED IT! It let go AGAIN. For all of you that have had good results, I'd like to know if it was on flat surfaces or inside curves because it didn't work for me. I'm going to do what I should have done in the first place. Buy 3M and start over. I don't know if theirs is any better but it can't be any worse than this GARBAGE.UPDATE. I just had to come back to update this review. After spending an hour covering a console with this JUNK,I hesitantly installed it. Thank goodness it was my own car and not someone elses. I had to have emergency surgery and my car was parked for 2 weeks until I could drive it again. I opened the door to get in and immediately noticed that the covering had turned loose, wrinkled up and DIED. After 2 hours and a pint of paint thinner I was able to get all the adhesive off the piece. I decided to give up on this stuff and just painted the console piece with black gloss for plastics. It looks great now!

This was my first vinyl job ever and this stuff was absolutely forgiving if you have a little sense and watch a few vids you will do very good it heats up and stays hot for about 15 seconds plenty of time to do what you need. I would and probably will buy this again in the near future. Oh and it's not a flat sticker it's actually got texture and shines and sparkles in the light out of 5 I give this a 7

Looks great

Nice wrap

That was used to do a protection band on both side of a pickup truck, made the truck look classier and give a good protection to the paint! Great look and finish

Easy to apply. I used this to cover a table top for my DJ gear and it works and looks great.

The vinyl looks really good when installed correctly. Light hits the 3 dimensional design and you get a true raw CF look at a glance. The vinyl itself is thin so moderate amount of heat will have it conforming to a lot of bends and curves. If you've worked with form fitting adheasive vinyl before then this is no different. For those starting out, you may want to work on a small moderately complex shape to get your heating and forming technique down. I love the look. If you seal it with automotive clear coat, make sure to go through the whole sand and spray process to get the best results.