GM Genuine Parts 23481275 Vapor Canister Vent Valve

Fits great, easy to install once you remove spare tire. Bought it for a 2007 Cadillac Escalade ESV. Kept getting an annoying Po446-po449 and had nozzle kept clicking off when getting gas. This fixed everything no more check engine light, no more clicking off at the pump and gained 3MPG. Absolutely worth it.

Worked as it should. Install wasn't the hardest and it's an OE part so it should last long enough. Now I can pump my gas in a 3rd of the time.

I bought this to solve the p0442 code I was getting on my Chevy Avalanche 5.3 FLEX. I first change the gas cap that can cause this code which is cheaper and easier. You want to rule the gas cap out first. In my case it did not fix the problem so I had to purchase this Vent Valve which is a common problem with this vehicle. It is relatively easy to change. The most difficult part is to lower and remove the spare tire from the truck, and dealing with all the dirt that fall in your face as you work under the truck. Wear goggles and\or hose off the dirt first <smile>. If you have not done this type of thing before, pay attention to the vacuum hose connector. You have to push in the plastic clip to remove or else you will have a hard time taking the old one off and brute force will break or crack the cannister nipple and put you in deeper trouble. Look closely at the new one first to see how it works and then take off the old one - it should slip off easy. The new bracket is shaped differently but still connect to the original bolt location. One more thing... You will need the Jumper Wire Harness - ACDelco 19257603 - BUY IT! You will thank me later.

I have a 2009 Chevy Tahoe that issued a P0449 Code. I bought this and the ACDelco 19257603 plug adapter. This was very easy to change and took me about 1hr. It took 30 min to get the stupid spare tire off. It was stuck and I had to use a long screw driver to release the safety lock. This canister comes with a new steel bracket and all new hoses. I absolutely needed the ACDELCO 19257603 Adapter since this canister has the updated electrical plug. This is an updated canister. The hoses are shaped a bit different than the factory original. I had the route the stiff hose under the charcoal box then up instead of above it and then down. This was a non-issue but just wanted to make a note of it. The flexible breather hose fit fine and came with zip ties to fasten it to the frame. Also note that this will not fit the old steel bracket. The canister comes with a new bracket and I had to use it to get the canister to sit in the correct position. The old bracket will causes the canister to be installed incorrectly which will pinch the stiff pipe. The new bracket worked perfect and all the pipes fit as they should - use a 13mm wrench to remove the single bolt holding it on the frame.. Overall this was a very easy change and the only tools I needed was a 13mm wrench, flat screw driver, and wire cutters to cut the old zip ties, and a $10 code reader to reset the code.

Did not match-up identical to the evap solenoid on my 07 suburban. Concept was all the same but the mount position to the hose in/out positions along with the small canister were all different from original. Functional it will install and work, but I feel that the hose that leads to the charcoal canister is not form fitted as well as the orginal. It feels as if its force to fit its position but it will connect and work. You do have to use the adapter plug and once all connected, the error code never comes back! FYI - this is what my oem part looked like... ACDelco 214-2341, problem was that it didn't come with the permanently attached hoses. One of the fittings were fore a slide on hose where as my OEM had a permanent press form fit hose which I could not remove & re -apply to this ACDelco 214-2341 part. So in a nut shell I just couldn't find the exact fit part that originally came off my truck , so when you come across the same situation with this ACDelco 23481275 part, don't panic... it will work.

Worked great. Cleared the P0449 code. Does not come with wiring harness adapter, so check if you need that. Has all necessary mounting hardware. I had to run mine a little differently because the hose from the canister to the other canister is alot longer than my shorter one i removed from my truck, but not a big deal. Had to maneuver the wiring from truck a little bit since that longer hose made the wiring harnes farther away, but we are talking about irrelevant issues. None of these things take more than about 30 seconds to solve. Nice that the hose has two way zip ties on it already. In all honesty, you really don't even need to use the new mounting bracket. Its heavier than the whole unit, so you could grab a handful of foot long or longer zip ties and just tie it up somewhere. If you can't figure out this install , you need to get out from under your vehicle.

Fixed my fueling issue on my 2007 chevy suburban.

Don’t forget to buy the adapter for it! It’s the reason for the 3 stars. It’s easy to install and does fit in place of the original but you need an adapter to the original plug. Other ones give you the adapter included. Weird also since this is a “GM” part.

También hay que reemplazarlo de vez en cuando

Very good part, fixed my problem with engine lite and now works fine . thanks.

The GM agency asked for 6000 dhs to fix the problem i had that when i stop at a gas station , the fuel pump keeps stopping when fueling which was super annoying and it takes so much time to fill a full tank, watched a couple of YouTube videos on how to fix this issue and bought this amazing product which came from the USA within 5 days with normal shipping, the installation took me 1 hr and i had no previous mechanical experience, very easy to install and the problem was solved and no more check engine light, very happy and satisfied

لم احصل على فيشة الكهرباء منتج ناقص

Pieza original