PROYAMA 58CC 2-Cycle Gas Powered Chainsaw, 16-Inch Top Handle Chain Saw, Gasoline Chainsaw 20-Inch for Tree Wood Cutting

I've always owned either Stihl or Echo yard tools, but while shopping for a bigger chainsaw, some Proyama review videos started popping up on YouTube. I ended up watching more than a dozen review videos by professional tree cutters and average homeowners that were comparing the Proyama chain saws to some much higher-end and more expensive chainsaws out there. The Proyama stood up well to the "big boys" and I was impressed by all the comparison videos I watched. I needed at least a 24" bar, and I was shocked when I looked up the price on Amazon. Less than $300 for a 68CC chainsaw with a 24" bar AND a 20" bar! WHAT? How is that even possible?? I was a bit skeptical, but figured this would be the perfect companion to my 16" Stihl chainsaw. And at a price LESS than I paid for the much smaller and less powerful Stihl. Needless to say, I was a little worried about the quality when I placed the order. I mean, how good can a big chainsaw be with a price like that? Well... The saw arrived within a couple days and it only took me about 30 minutes to get it all unboxed and ready to cut. Since it was getting late, I was only able to test it on a couple smaller logs and one tree branch in my back yard. It started right up on the 4th pull and ran like a beast! The motor feels and sounds very powerful. It ripped through my test logs and tree branch fast with no issue. Nice big wood chips, which is just what I like to see from a sharp chain. The next morning, I went over to my sons house to cut down a large tree stump that was about 22" in diameter. This is one of the reasons I needed a bigger saw because my little 16" Stihl was not up to the task. The Proyama ripped through the large stump in 1 minute of actual cutting which you can see in the included video. The motor is very powerful and the chain extremely sharp! The saw is easy to operate, feels good in the hands, and can definitely go toe-to-toe with higher ends saws like Stihl, Echo, or Husqvarna. For the price Proyama charges, I am very impressed with the quality and value provided with this saw. I was also pleasantly surprised to also receive a face shield, hearing protection, gloves, a fuel mixing bottle, and a toolkit that even includes a sharpening file! Proyama is doing it right, and every homeowner (or even professional) should give their outdoor power equipment a serious look!

1) The 68cc model is actually 62cc. Some Chinese manufacturers count the squish as displacement, which is not the case anywhere else in the world, so know you're actually buying a 62cc when you buy the PCS68. That said, it's a solid 62cc motor that runs with similar power to a 60ish CC saw from one of the big mfgs who will charge you at least double for a saw in this class with 2 bars and chains. This motor has every bit as much power (likely a bit more) as an Echo 590 or similar, but if you think you're getting a 70cc pro saw for 1/6 the cost...lol. Saw goes together quick and easy, put some loctite on the dogs you muppets! Some reviewers had complaints about the chain tensioner breaking...user error, that happens when people run the saw with loose bar nuts. Speaking of which, would recommend replacing them with nylon lock nuts to prevent that from ever happening. Cheap insurance for a buck or two at your local hardware store. This saw does have a bit more vibration than a big name saw with a modern anti-vibe, not an issue for the vast majority of people, but something to be aware of. Saw fires right up and runs awesome right out of the box. First start of the day requires about 3 pulls, after that even if slightly warm, it fires up 1 pull, no choke. EZ start works great. Tons of power, this thing EATS even with the safety chain they give you. Throw a nice full chisel on it and you'll be through large hardwood quick and easy. There is a lot of cutting speed to be gained with a real chain, but the one provided still cuts well. It's LOUD! There's nothing in the muffler, it's just a can, so there's no need to disassemble it to get rid of the useless spark arrestor screen, which is usually the first thing i do on 2 stroke equipment to prevent future clogging issues. If you're sensitive to a loud saw, it could be an issue for you. If you're cutting 10 cords of firewood in the middle of suburbia, better cut some for your neighbors to apologize after making them listen to this big nasty thang. Running it next to a 40cc husky, it's seriously about twice as loud. What else...bar oil! With the factory oiler setting it does go through it quickly. I'd leave it as is if using the 24" bar in big wood. If using the 20" bar in smaller stuff, you may want to turn it down a bit. Personally, i've just left it and refill with every refuel. The choke is a little janky, and plastics are decent (great for a clone saw, but definitely not name brand quality), but nothing that is a real issue. I've read some people have melted the plastics, so before i ran my saw i shoved a 3/8" extension into the exhaust ports and used it to bend the tips straight ahead to direct the exhaust forward, away from the plastics and chain bake. Mine have not melted. Bottom line, this is an exceptional saw for the money paid, and i'd recommend it to anyone. I don't think you're going to get better value for dollar, and this unit is solidly built and very capable.

My old Poulan 38cc finally bit the dust after 33 years and dropping it's last tree 8 days ago. I got the tree on the ground and cut/burned all of the top limbs. Took a break before starting on the main trunk, which was about 18" Ø at the base and about 30 feet long. Tried to start the old saw but realized it had finally died. I realized I needed to buy a new chainsaw, and began looking online for some of the better rated saws. It didn't take long to realize that I'd spend around $400 + for a name-brand saw with a bar that's 16 inches or longer. And then I came across this Proyama 58cc saw, with not only a 16" bar & chain but also a 20" bar & chain as well. Reviews looked pretty good considering the price, and it has all of the nice features of a decent saw, like a chain brake, ease of chain adjustment and refilling the oil & fuel tanks, and easy starting. A few of the reviews stated that this saw was really hard to start, but I had no problem. Just followed the directions to the letter, and it cranked right up on the 3rd pull after the preliminary start-up procedure. I let it idle for about 30 minutes to sort of break-in, and then went to work. WOW, was I impressed with the 1st cut and beyond. Lots of power. That 30 feet of trunk was cut up in about 20 minutes at approximately 2 feet per cut. I had to restart the saw a couple of times after shutting it off, and it started right up without any hesitation. It handles well and the weight is easily maneuvered. This has been my 1st & only experience with this named brand saw, but I'm well pleased with the initial performance. Hopefully it will serve me well for many years to come. I took out out the extended 3 year warranty, so for around a total price of $200, I feel I bought a bargain and that it's protected. One particular note I'd like to mention regarding several of the reviews that had a low rating: I realized at the time of reading them there may have been error at the time of assembly. There's always the possibility a "lemon" shows up from the factory, but If you're mechanically inclined, read the instructions carefully, use a little common sense, and know what to look for while assembling, then you should have no problem with this saw. Otherwise, if you're not sure, find someone with experience or a professional and let them setup the saw for you. When I was assembling this saw, there were a couple of things I had to stop, look, and examine more thoroughly to make sure it was done correctly. Especially making sure the chain was on the sprocket at the clutch and not directly against the clutch. When I thought it was assembled but the chain wouldn't spin, it was time to back up and look more closely at what I had done. Otherwise, it could have meant premature failure on some components. Hopefully whoever reads this will find it helpful if trying to make a decision on buying a new saw, or if doing the assembly yourself. Best regards, KMS

I'm a homeowner that burns 5-8 cords of wood per winter. When I was young I worked in logging and used only STIHL 36" chainsaws. I'm 59 years old now and dont have the strength or stamina I did when I was younger! This saw is HEAVY compared to smaller ones. Most importantly? IT CAN POWER THROUGH BIG PIECES OF WOOD QUICKLY! I have tree removal companies dump off wood in 6' lengths, which they do for free. I then slice it into 18" pieces and use a 30 ton log splitter to break them up and then a smaller 5 ton splitter to make fire wood. In the picture you see the logs from both tree company 'dumps' in my driveway. I used the 24" bar and the 24" chain that came with the saw. It made quick work of these 36" diameter logs. Others had problems: 1. Reported not to start after first time or wouldn't start after sitting for a while. I didn't experience this. I'm also smart so after I was done cutting up one load I'd pour the gas out of the saw and put it back in my gas can, then I'd start the saw and just let it die from not having any gas. When the next load came it started right up - no problems (see starting procedures below). 2. It EATS bar oil! Well the setting for the amount of bar oil is explained in the (rather lame) directions. USE THAT SMALL SCREW TO ADJUST! I've ALWAYS used old oil that came from my car's oil changes for bar oil - it works great! After adjusting that screw - it ate oil about the same as I remember my Stihl's back in the day. 3. Darnit folks - CLEAN the air filter after each day of cutting! 4. The 'gas container'. Yeah - it's worthless for gas. Get a 1 gallon red gas can at your local store and use it. The new ones have a cut-off and the nozzle fits the hole of the gas on the saw. I use the gas container they sent for chain oil. (yeah - I use oil from my car's oil changes so I need a container for that) 5. YES - holes for gas and chain oil are small. Buy a few small funnels and have some paper towels or rags around to wipe up because you WILL spill! Problems I had: 1. The jagged piece of metal that you put on to help you 'dig' into the wood and get leverage - the screws kept coming lose. I replaced the factory screws (which were hex - I freaking HATE hex) with two stainless screws from the hardware store using lock-washers to keep them tight. I'd recommend putting lock washers on your factory hex screws and DONT misplace the hex driver that came with the saw. 2. The tool to tighten the saw. It broke straight away. I'm using a ratchet and deep well socket now - it works great. The screwdriver they give to you is also useless - use a real one! 3. Chainsaw chains. Folks - regardless of what powerful motor you use, if the chain is dull it wont cut! I had largely forgotten about sharpening, bar lubrication, and chains all together since I was young. 4. Chainsaw chains get HOT when cutting through very thick wood especially when the chain isn't very sharp. STARTING COLD: *With gas in it already: Push the fuel bulb once, pull the choke out, put your foot on the bottom of the handle and pull the cord. It should 'sputter' after 2 or 3 pulls - when it does, push the choke back in and pull the cord - it'll start after 3-4 pulls. *With NO gas in it: Push the fuel bulb 2-3 times - follow above directions. It's a darn good saw with plenty of power and a GREAT price-point that I'm HAPPY to own and I'm sure it will last! As I said above, I'm 59 years old - but I'm still VERY strong. I can use this saw for a few hours before I get worn out. p.s. The 'safety gear'?? Yeah - useless! Ear muffs aren't bad - I dont use them as my hearing is shot already. There's an old saying, "You get what you pay for". Well folks, this isn't a STIHL or HUSQ but DARN it's got power and if you keep your chain sharp it'll cut though some massive wood. HIGHLY RECOMMENDED! UPDATE: I've got through the two loads of wood in the pictures above - the latest load was red oak. The base of the tree was about 30 inches. In all I'm guessing I've ran this saw for about 50 hours so I have a bit more to say. Oak is considerably denser than pine. This saw, with a new chain, powered through the 30 inch diameter with no problems (one cut from each side - about 90 seconds total). THE CARDBOARD What in God's green earth is the cardboard for? What purpose does it serve? It says in the manual, "do not let the cardboard get oily. Well darnit - it's right where the chain gets oil. By the third chain replacement, the cardboard was soaked with oil and disintegrating. THE BAR At the front is a sprocket. I forgot about lubricating that. My saw just couldn't cut straight. The sprocket was overheating. There's a very small hole near the center of the sprocket on either side. Either use a grease gun or just push grease down that hole with your finger, spin the sprocket and more grease. I also turn the bar upside down every time I sharpen the chain - that way the sprocket spins in the opposite direction and wears more even. CHAINS I cut my wood on my concrete driveway so that once a piece is cut off, I use a furniture dolly to move it. (work smarter not harder). DO NOT dig your chain into dirt EVER or let it hit stones or metal. If you do, it will dull your chain. I had to relearn about chain sharpening. Trust me on this - buy a set of chainsaw files and use them - DO NOT WASTE YOUR MONEY ON ANYTHING ELSE (I did). What kind of chain you should use is up to what you're cutting. My 'end product' is cord-wood that I burn so I dont care if there's teeth marks in the wood I cut. After sharpening and using the chain that came with this saw, it was taking me about 3-4 minutes to make two cuts in the 30" oak. I bought a full chisel skip tooth chain. See, the chain that comes with the saw is a 'safety' chain and helps the saw from 'bucking' back. While it's probably a good thing for the 'new' chainsaw user, it doesn't cut as fast. The full chisel skip tooth chain allowed me to cut that same slice in about 90 seconds. I'm very strong so I'm able to handle it occasionally 'bucking' on me. Summary: VERY NICE SAW THAT IS AFFORDABLE! 1. If you are comfortable with chainsaws - get a full chisel skip tooth chain for this saw - you'll thank me! 2. Keep it clean. 3. Keep your bar's sprocket lubricated! (if your cuts dont go straight no matter what - your sprocket needs lubricated - do so then turn the bar upside down) 4. Buy this kit and USE IT! www.amazon.com/gp/product/B082PJ4CP5/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 But - whenever your sharpen your chain, run the flat file over the top of each 'raker' (or 'follower')on the chain - just ONE pull! 5. Starting - if you cant start yours, let it sit for an hour and try my directions above (cold start).

So like most I was skeptical. Needed a bigger saw to take down a massive pine tree. I went through the saw and made sure everything was tight and several screws needed tightening. After that it fired right up in 3 pulls and ran very strong. I did a 2 stroke engine break in procedure for two tanks of gas to break it in nice and easy. After that I cut down this beast of a tree (about 40” base) and chopped the entire thing up in a day. I ran 8-10 tanks of fuel through it and this thing runs great and cuts like a beast. Towards the end of the day I tuned the carb because it was running a tad rich and now it rips even stronger and cuts so good. I’m sure this will not be a 20 year saw like the name brands but for the limited time I need a saw this big, with proper maintenance I’m sure it will do the trick. I could not be happier with how it performed. Even the stock chain I is great!! Really can’t beat what you get with this package for the money. Highly recommend for the homeowner who needs a 24” powerful saw without breaking the bank.

It took me 200 pulls to start this chainsaw. It comes in Amazon delivery, the box is secure for it to ship, however the people handling it will flip it, roll it, PROBABLY THROW IT. Its all still safe for this chainsaw. But DO NOT THINK YOU CAN PUT GAS IN IT AND START IT! DO NOT MAKE THAT MISTAKE! Remove the spark plug, fill the port up with carburetor cleaner, pull it a lot, flip it up with blade pointing to the ground, watch the grey metal junk from manufacturing process run out the exhaust muffler, DO THAT PROCESS A FEW TIMES, CLEAN THE SPARK PLUG, IT WILL BE LOADED WITH JUNK (METAL OILY JUNK FROM MANUFACTURING PROCESS), only then that you have confirmed it's completely clean can you put fuel in it and attempt to start. It will then start on first pull and it's a badass saw and lets be honest you are here like me because you did not want to spend $800-900 on a real 24" bar chainsaw like a Husqvarna. If you do not do these steps you will pull it 200 times and be very very angry you bought a piece of junk made in CHYNA that will not start. Only gave 3 stars for the pain I went through trying to get it to run. So to conclude likely from shipping the manufacturing oil in the chainsaw will go everywhere and it will not start until you clean it! Update: had to order a replacement spark plug, went with NGK, now causes the saw to idle higher I assume because a hotter spark but at least it runs, so I need to take the left side case off and adjust the T screw for the idle. Saw runs good but to be honest I rather have just spent another $500 on a Husqvarna and bought a real saw I don't have to do anything but use it. Plus it would clearly be made better.

I bought this 24” chainsaw to back up a 20” Farm Boss and a 20” Timber Wolf -we’re dealing with some large caliber trees that went down in the winter’s ice storm. To be honest, I went with this model because of the price not because I knew anything about Proyama quality. I read all the negative reviews on Amazon but there will always be negative reviews. I took my chances and am glad I did. The chainsaw is extremely well packaged, box within box within box. It comes with the accessories as advertised and of course an extra 20” bar and chain, and that makes this an especially good deal. The primer bulb was half full of gas and customer service confirmed these chainsaws are tested in the factory before shipment. The owner’s manual is comprehensive and there are also separate picture guides for assembly and start up. Other reviewers mention using a 25:1 mixture for break-in. I didn’t see any reference to that. The chainsaw and the manual both say 40:1 and that’s what I used out of the gate. Six pushes on the bulb filled it up, two pulls with the choke out to a pop and then two pulls fired it up. I know it’s brand new but that’s amazing - never had a Stihl or Echo start so easily. I’ve only tested it in the field - cut some rounds off the top of a 16” standing stump. Easily to handle, cuts well, idles fine, chain brake works. The included bar is sturdy and the chain of course is sharp - a more aggressive chain can be installed but is not really necessary for most users. I did have a question for customers service and was concerned that the only way to contact was via email. However, wherever they are, they respond quickly and to the point. This I think is a big plus. Much better than waiting on hold forever to finally talk to someone who is not familiar with the product. As noted, I haven’t yet put this chainsaw through its paces but so far I’m extremely pleased.

This thing is hard to beat for the money. On first startup everything was great. I put it under a little load and it wasn't what I would call the perfect smoothest reving saw. It cut very nice and ran well. Just didn't seem like it was quite as smooth as other saws. However, the more I ran it, the better it got.I think it needs some heat cycles like a break in time. I have now ran several gallons through the saw. The thing starts easily cuts well. I would definitely recommend it.

I ran Husqvarna saws all my life and I bought this saw just to see and I’m seriously impressed, she turns up, definitely worth the money.

Chainsaw didn't work when I msged them about it they couldn't give me a return shipping code so gave me a $74 refund

لايوجد بالسوق الالكتروني جنازير تناسب قياسات المنشار ك :- جنزير منشار ZM 18-64-58-3/8 أو جنزير منشار ZM 22-64-58-3/8

Make sure when you assemble to take the chain brake off because you will not be able to fit that piece onto the chainsaw. The metal ring fits around the clutch, if you don't release the brake release that metal ring isn't round it's oval and you will not be able to put it on. Took me a good 10 mins to figure it out. Initially the chain oil was leaking all over the bottom but after a short while the leaking stop. I think the bar gasket had to become wet I don't know but the leaking stopped and it's working as good as my Shindaiwa 488 Pro. 2 metal bars, 18" and 22" I bought, both are made of metal, similar bars are like $150-175 here on Amazon, imagine, the two bars pays for the whole chainsaw and it comes with cheap accessories, but still it comes with accessories that you can use, the helmet not the safest but the face guard is alright, it came with the saw so I will not knock the quality of the accessories. I'm confident if it breaks down I'll be able to replace any parts. I will be ordering many of the (cardboard-type) bar-gasket that came with it I suspect that gasket will not last long. I suspect lots of leakage if that gasket isn't replaced often. I give this full stars hoping it doesn't brake down before 3 years of weekly use.

So far I’m giving it 3 stars as I just unboxed it & put it together. If Mother Nature cooperates tomorrow I’ll mix up some gas and try it. This is my first 68cc chainsaw. Opening the box I found the face shield broken and signs in the box that stuff has been moving around a lot but I didn’t see anything else bent or broken. Putting it together you can tell that it isn’t a Stihl or Husqvarna. I have both a Stihl 271 Farm boss with a 20” bar and a Husqvarna 262XP with a 20” bar. Putting the chain on this one took me a little bit to put it on compared to my other saws. The chain tension adjuster is just made out of plastic so we’ll see how long it lasts. This saw came with a 20” and 24” bar and chains. I put the 24” on to try since I have a big oak dropped already to finish up cutting. I will update this after I’ve tried the saw out. I still haven’t been out cutting yet -23 with wind chill right now. I did mix up some gas, & filled it with gas & bar oil. I had to press the primer around 25 times before it filled with gas then 2 more times before I tried starting it. It kicked on the forth pull so I moved the choke in some & it fired then stalled. Had to put choke all the way on then it started & ran good. It feels powerful. Ran it for a couple min running the chain then stopped it. Chain loosened up a lot more than I was expecting so I tightened it back to where I like running my chains. Let it sit for about 5 min & tried to start it & it fired & ran on first pull. It also idles good. I’ll update again after I’ve cut some wood with it. I finally made it out to cut. As you can see from my pictures I’m working on a big Red Oak. What can I say I’m impressed it’s cutting through like a hot knife through butter. I have the 24” bar & chain on it & there’s no shortage of power it’s as good or better then my Stihl & Husqvarna. It does seem hard on gas so far but it just finished its first tank. After running out I refilled it & hit the primer once & it started right up. Also after riding around in the back of my truck (covered) it started right up after priming it 3 times it kicked first pull & started second after shutting off the choke.