Universal Dash Cam Mount for Rove R2-4K, R2-4K Pro, R2-4K Dual, Redtiger Dash Cam - Suction Cup Replacement – Stable Rearview Mirror Holder Bracket Kit

I'm very happy with this so far! My Rove camera kept falling from the windshield using their suction cup; it just couldn't take the Texas heat in the summer. I wasn't sure if I would like having this sit further from the windshield, but the picture is just fine. I'm using this in a Jeep Wranger JL and it mounts fine to the mirror. The only thing I would change is I wish they would include shorter mounting screws. I plan on getting a smaller set and using locking nuts instead of the wingnuts. It's very sturdy and a good price.

Product came with multiple attachments for different cameras. Very easy to install. I am happy that I decided to get this mount.

I bought this because the suction attachment that came with my dashcam does not work due to the bumpy dot pattern that's part of the tint line area on the windshield (prevents suction). There are 2 brackets for this type of camera in the kit. The less wide one fits snugly side to side on the attachment; however the "arms" are slightly too short to allow for the attachment screw to go all the way through without having to be bent (holes don't completely line up. The wider bracket leaves a lot of open space for camera to slide around (which makes it unusable since it's not steady/fixed). Bought another kit from different company - same issue. THE FIX FOR THIS: go to the local hardware store and get a screw that's 6mm by at least 2" long, a nut, and several washers (I think I used 10-11 washers). I placed the camera mounting against the side of the bracket that has the ridging for added stability when adjusting angle, then filled the remaining space with the washers and tightened it all down with the nut. Not the prettiest, but stable and functional. **Note for picture: I have not hooked up rear camera yet so it is missing a cable between mounting bracket and power supply cable in the picture... the screw will get in way if not mounted in this fashion (1.5" screw is too short).

I purchased this for use with my Vantrue N2 Pro dash cam. Directly behind my car's rear view mirror is a fairly large case housing connected to the windshield which houses various sensors. Unfortunately the plastic case is large enough that it creates a blind spot in the camera's view when the dash cam is mounted directly on my windshield. If I wanted to keep the dash cam on my windshield, I would've had to place it very low which would have looked tacky and would have been a constant distraction in my line of sight while driving. This rear view mirror mount is G-R-E-A-T and you get a lot for the price. It comes with many different mounting connectors to accommodate dash cams of various types. The set that I received has a connector that fits my N2 Pro tightly without coming into contact with the charging pins on the dash cam itself. However, there are a couple areas that I feel could use improvement: 1. The connector that works with the Vantrue N2 Pro connects tightly to the dash cam, which is great for making sure that the dash cam stays secure while mounted. But it does make for a bit of a hassle when you need to disconnect the dash cam from the mount. 2. The mirror mount has two adjustable ball joints (which is great), however there is only one screw that lets you adjust the tightness of movement for both ball joints. It would be nice if each ball joint had it's own form of adjustment so that you could lock one in place but still be able to set the second joint at a different level of resistance. Overall, I'm VERY happy with this mount as it helped to keep my windshield uncluttered.

I have a dash cam in each of our four cars; all but one came with a suction cup mount and if you're looking at this item and reading these reviews, you know they suck...er, stop sucking. This kit has a variety of adapters that should work with most cams. There's even an adapter for a GoPro mount or other small camera. I'm using this on two different models of cams. One just needed the correct included adapter, but the other required part of the cam's existing windshield mount, along with the included U bracket adapter. Although it can get awkward trying to work with the mirror's arm, installation is fairly easy and the instructions are written well. The ball joints allow you to position the cam more or less where you want/need it. Just make sure you fully tighten everything after it's in place. I haven't gone off-road or driven on extremely bad roads, but so far they haven't shifted and don't seem to move any more than the original mounts did. The kit comes with the assorted pieces and instructions in a sealed plastic bag. I ordered three kits and although I didn't need it, one package was missing the small U bracket. So that's one star off for quality control - someone else might have needed it. Also, make sure this will work in your car. That is to say, that your car's rearview mirror actually has an arm to attach it to. I ordered in haste without looking and my Hyundai Sonata's mirror doesn't have the standard arm mount. I was able to rig it up and it's holding okay so far, but wouldn't recommend this unless you're positive your car has some kind of arm this can fit around. Otherwise it's a nice solution and would definitely recommend it to replace those destined-to-fail suction mounts. ***Update*** After using these for almost a year, I have to come back and take away a star. The joints tend to loosen after a short while and you need to periodically re-tighten them. Which honestly hasn't been that big of a deal...until today when one of the plastic screw grips broke off. It's still functional as I can tighten the nut it was holding, but now I need to use pliers, etc. It still works well enough, and still better than suction cups, but I'm also expecting the same thing to happen in my other two vehicles.

Update: After posting this review, I received a new joint piece for my camera and it is the perfect fit. I thank the seller for the quick correspondence! The camera is now very secure. The installation was quick and easy. It does not move around during travels. This mount is made very well overall. I got it because I am afraid that a suction cup on my windshield in the hot climate would fall off. I loved everything about this mirror mount except for the fact that one of the joints that it came with does not fit the KDLINKS X1 Dash camera very securely, and therefore it falls off too easily. The product says it fits this camera so I am wondering if maybe I just got a smaller-than-usual piece. When I secured the camera to the suction cup that it came with, it was much more secure so I believe that the piece I got was not made correctly.

Ordered this product to mount my dash camera from the mirror of my 2010 Silverado. It was auper easy to install and tightened the bracket down finger tight (no tools). The camera seemed to bounce/shake a little from the mirror. I didn’t have this problem with the original mount of the dash camera. After a few days the clamp part around the mirror stem broke making this product absolutely useless and a waste of money and time. This product is a great idea, but make from cheap parts. I definitely would not recommend this product.

Bought this exact mount from the same seller back in 2019. I bought this again because I didn't realize my Yi camera was broken and not the actual mount. The mount lasted longer than my camera in the Florida heat.

Thanks to the provided rubber strips, it fits my BMW e60 in tilted condition. Now, my dash cam is secured and not falling down after sun heat on the windshield. Recommended & thanks!!

These products very useful to what i need for. Seller is good to and speed delivery!

I want a mount that was solid and would work in the cold. This was a great fit for my needs.

Bad

Pretty awesome, I don't know why I never thought of getting one of these before. I've had a dash for over a year now and the suction cup recently gave up. Cleaned it with rubbing alcohol and it started to stick to the glass properly again, however I stumbled across this one day and knew that this would be a much better option than using a suction cup or adhesive. Reasons not not to use the suction cup: They lose suction after awhile. Reason not to use glue strips: they leave nasty adhesive on your windshield which may be hard to remove. This mount kit provides a good amount of adjustability and accessibility to your dashcam. there are multiple connections to connect to all different types of dashcams. The only issue i had was the fact that you really have to get up and close to your mirror to connect everything, so if you have a tightly spaced car you might have a little trouble, the job could be done a lot quicker with two people.