Utheer 60040 Grill Burner Tube for Weber Q1200 Q1000 Q100 Q120

For my Weber Spirit E310 with front ignition from 2015: five stars based purely on initial impressions: a perfect fit, surprisingly easy installation, and excellent function, at a fair price. It got my grill to 600 degrees. Don't waste time messing with old rusty burners and crossover tubes with clogged holes like I did, this should be a no brainer.

I knew this kit came with burners, which is what I needed. I had no idea it came with EVERYTHING. I was happily surprised. This kit came with 3 new burners and that funky crossbar that allows the first burner to ignite the second and third ones. It also came with those pesky little screws that anchor the burners in place (I had to use a propane blowtorch to get the old ones out). AND the complete igniter: the push-button, the igniter body, all cables, and the actually plastic / spark creating piece that anchors onto the first burner. And the five flavor bars. From start to finish it took me about 90 minutes to tear apart and reassemble the grill with the new components (Weber spirit 3-burner). It would have gone faster if those three original screws weren't so difficult to remove (I needed a propane torch to get them loose.) After some WD-40, the new ones went in like butter. I'm sure Weber will scoff at this being after-market, but every single component fit perfectly. The igniter wires were a little different from the originals, but again, if you're a DIYer you'll figure it out in 30 seconds. Bottom line, this kit *is* for a DIYer. If you aren't, you'll probably get a little frustrated, or bend something. Just get some disposable gloves and some clothes you won't mind getting dirty, and have at it. This kit is great and is the sort of tune-up that gave my grill a second lease on life. I was really trying to avoid having to get a completely new grill. My grill is already 8 years old. This refurb along with a good cleaning, rust treatment and paint, I think I'll get at least four or five more years of life out of it. Bottom line, I'd recommend this kit.

These burner tubes worked perfectly and were very easy to install. Note to installer: It is not necessary to take the front panel off. Just pull the old ones out from in the grill and there is enough play in the starter line to unclip the starter from the burner. To remove the clip you need to slide the clip back towards you as you hold the burner tube. There are two small tabs on either side of the starter that you will need to pry up a bit for it to slide all the way back. Then just position the new burner tube in place and snap the starter in the new tube. That's it. Happy Grilling

Fit perfectly in my Weber. Seems to be good quality. Grilll is working like new again.

Compared to the original components, two burner tubes were unable to fully secure while the last bolt tightened the end just fine. I think they were just a hair thinner than the original ends, not a big deal. I replaced everything in the kit and it fired up just fine. Performance wise, the new burners sputters at the lowest heat setting. Otherwise on mid to high heat, performed like a new grill. I bought this kit because it was way cheaper than original Weber parts. Highly recommended if you want to save money. The biggest difference I noticed between my original burners vs these new ones. Maybe that’s why it doesn’t have better heat control at the lower end. I’ll keep messing with it and see if there’s any modifications I can make. Only issue keeping it from 5 stars

This product looks exactly like the original "Webber" product. I bought the 3 burner (Natural Gas) grill at Home Depot about 6 to 8 years ago. I have contacted Webber to warranty parts in the past but for some reason I bought this replacement kit. I am glad I did- finally I got my ignitor back again. For the last year or 2 the ignitor just didn't lite the burner. I tried new batteries and bending the electrode, I wrapped a copper wire around the burner near the ignitor but nothing worked. I am a HVAC service tech so I am use to working on furnaces so this wasn't too hard to figure out. I decided to make it more challenging by doing it after dark with a flashlight. Remember to Shut Off the gas supply first. The main thing is to take the front control panel off and let it dangle by the internal gas line while you pull the burners out. A lot of Phillip's screws and two- 7/16" bolts hold panel in place. Also take the gas line support loose on the right side. Don't disconnect or severely bend the internal gas line. The washer headed screws at the back of the burners were hopelessly rusted in place. Fortunately the burners slid out under them I pulled out burners through the front. The left burner has a clip that holds the ignitor electrode in place. The mounting bracket on the new burner had to be pried up to get the ignitor to slide in place. Be careful use a flat blade screwdriver and pry just enough to get it to slide. This tight connection is critical and I think why my old one wasn't sparking right. This provides the grounded connection for the ignitor. It has to fit tight metal to metal. Make sure it pushes tightly and completely into place. Rout the wires just like the old ignitor system. The electric control module fits in place just like the old one and the wires are easy to figure out. While the burners were out I cleaned up the burner bowl and used pliers to grab the 3 rusted screws in the back of the burners and slowly unscrewed them. The kit came with 3 new screws. The screws don't hold the burners tight. They do keep the burners in place. The burners are all different so each of the three fit in only one way. Put the crossover tube and burners together carefully - study them to be sure the flame holes all face the right way and that the crossover tube will carry the flame across the the next burner. After it's all back together it lit with the ignitor but the flame jumps around off the burners and the burners didn't stay completely lit. This is the important tip that the instructions don't mention---- each burner has an air shutter at the front end that may need to be adjusted. The shutters also have a metal screen to keep bugs out - don't remove the screens Just loosen or remove the shutter set screw with the burners working and carefully adjust the shutters to make the flame stabilize. This is easier in the dark so you can see the flame. A well defined blue flame is what you want. I found closing the shutters to 1/4 to 1/3 open worked best for my grill. Watch the flame on the cross over tube as well it should be small but a continuous string of flames. Move the control knobs slowly between hi and low and make sure the burners are blue and stable. Don't just go for the biggest flame from the burners. Look for the largest well defined flame on high without a rolling/ dancing type flame. Tighten the set screws back to hold the shutters in place. Propane has a much higher pressure than natural gas so adjusting the burner shutters will be different but same thing applies look for a strong well defined blue flame on high. Orange tops on the flames are not good and should be adjusted out as much as possible using the shutters. Orange flames are inefficient flames and produce more carbon monoxide they are usually more common in dirty or rusty burner tubes. I've cooked several steaks in the 2 weeks since I rebuilt the burner and it seems to work like new.

Easy to reinstall . BBQ looks like new again!!! Thick , heavy grill bars ..

Works great! Easy to install

Sehr schnelle Lieferung. Problemloser Einbau. Endlich wieder ein gleichmaessiges Grillbild und keine verbrannten Ecken. Naechstes Mal werde ich den Brenner frueher ersetzen. Gerne wieder.

Good quality

fit like it should and works perfect

Better than the original will be ordering a spare highly recommend if you own a webber Q

Working perfectly