DC HOUSE 12 Inch 12" High Speed 14mm/s Linear Actuator Motor 1000N DC12V with Mounting Brackets

I wanted to wait a while before reviewing this because I was concerned about longevity from such a relatively inexpensive linear motor. But "so far, so good" ... and I'll update this review if/when it fails at a later date. (Whoops; see update below.) I'm using it to open a fairly heavy wooden "man gate" in my backyard fence, and it has plenty of power to do so. I teamed it up with a remote fwd/reverse controller ( https://www.amazon.com/dp/B0CSN27T1D ), which worked out perfectly. I'm a little suspicious of its IP54 claim, but we've had tons of rain here and it's holding up well. I may add a simple rain cover for it soon, for additional protection from above. Update: At the 9 week mark, my fence gate had swollen with rain so that it wouldn't close all the way. But the motor was trying its darndest to close it. I found the gate problem some days later, and the motor had burned out. No fault of the motor, but beware that it WILL burn out if you keep power applied for a long period of time without it being able to move to its STOP open or close positions. Update 2: I ordered a replacement, and once it arrived I installed it onto my fence -- and found that its CLOSE position was about 1/8" shorter than the first one. The drilled hole in the rod is in the same position relative to its end. The issue seems to be that the STOP limit switch adjustment is a little different between units. It would be great if there was access to adjust those open and close limit switches, but there is not. So I had to move over my fence bracket that 1/8" to compensate.

Works great Easy to use No issues

Excellent actuator. Easy to use. We made pop-up 3d animal targets using this and an arduino kit.

Good product,Needs controller switch that is sold separately to function.

Item worked well

Generallly this works OK, and meets its specs. However, the machining of the mounting pin holes is shockingly bad. Ordinary good manufacturing practices produce products with better tolerances than a hobbyist machine shop can. This is much worse than hobbyist machining level. The pin hole (at the motor end) is not perpendicular to the rod, which can be checked by mounting the actuator in one position (eg. motor facing east), and then remounting it after rotating it 180 degrees. On mine, the difference in rod end position was about 1.5 inches, meaning that the hole was drilled a couple degrees from perpendicular. Some hand filing with a rat tail file trued mine up enough to prevent binding, but of course, the hole is no longer round or straight. Suggested improvements: stainless steel anchor brackets and pins to make it more suitable for use outdoors. And, of course, standard machining.

Works great. Plenty of power for my use.

I purchased two ECO LLC Linear Actuator 12V 1000N High Speed 10 Inch 10" Motor 14mm/s with Mounting Brackets on Amazon to be used in tandem. Unfortunately one is 8 seconds slower to full extension than the other. I timed them when wired separately and together. Also, I noticed that one actuator ran rather quietly and consistently and the other ran twice as loud (this is a guess since I didn't actually test the db) but the sound also fluctuated during operation. This suggests to me a faulty actuator. I reached out to the seller privately but did not receive a response. I will amend my review if they rectify they rectify the problem as one of the actuators seems to work fine.

Excelente calidad y funcionamiento. Lo utilice para un mecanismo de alas.

This was a great addition for my tractor snowblower shoot. Worked well during the summer when I installed it and worked good during the first few winter storms we had. The only issue I had was that the further it got cold out, the worst it got because it would freeze and wouldn't move. I understand that I am using in a creative way, definitely should have bought something more heavy duty. But no complaints about buying it.

I fully expected these to be terribly over rated for power and they are. Good for maybe 1/4 of their max rating, supposed to be roughly 1/2 of the stall rating. However they work well and I bought assuming they would have far less "push" than advertised.

Used for a week now, unit works very well. Quiet and strong. Feels very sturdy, I'm sure it will last for years and many hundreds of thousands of cycles.

Installé sur la chute de souffleur sur mon tracteur. Pas le plus rapide mais travaille bien. Je le recommande !!!