Gamo Cone Pellet Trap - Collapsible - 100 Paper Targets

works perfectly, it traps my gamo pellet gun just fine

This is a very good target if you have some experience. It's not big so if you are a beginner you will miss the target a lot. But if you have more experience you will hit it more often and will know you hit the target because of the metal noise it makes when you hit the target. Metal BBs are very strong and will cause some areas to bent and the paint to come off. One area that bents is the place where you insert the paper, so after some time you will have a harder time putting the paper targets in. But the most frustrating part is the metal pad that bents and doesn't allow the pellets to fall down on the rectangular shape collector. But you can open this pad with a tool and the BBs will fall there again. I gave 5 stars because its a great target and if you are a BB lover you should expect to buy more than one of these targets.

So I haven't had this long or have I put a lot of rounds into it but so far it's great! I use fire .20 and . 25 gram plastic airsoft bbs into it while I have it mounted on my wall in my tech room. No more bbs on the floor!!! Although the top I had to cover with cardboard and tape and down up and underneath the base were it slides into the wall holder mount part because 99% of all my bbs shattered upon impact, getting pieces everywhere lol. Once it's all taped up it works like a charm! 1000% clean. The shattered bbs don't bother me, I never reuse bbs fired from my barrels anyways. All in all it was a great buy for a great price and it's sturdy! I'll update the review if anything happens but so far it's getting the official Michael Approved stamp seal 👍 Update! Bent the hell outta the back metal plate. Strongest shots where from a 400fps bb at point blank range. Most are at 1 joule of energy or less. Still holding strong!

Super easy to assemble lots of targets for the money, but not up to .22 lead coming out of a PCP rifle I even have mine tunned down considerably lower than the factory settings. I was shooting at about 30 yards, as that is all the room I have. The attached images are after only shooting 10 rounds at the target. I was re-zeroing scope after re-installing, or the damage probably would have been much worse to the holder / down reflection piece. I had some 2 inch hi density foam that I cut to fit in it, which slows down lead enough to make it usable for me. I checked again after that 20 rounds with the foam and the back mostly the same, but the metal piece that reflects the lead down to was bent worse and cracked at the bottom. Ill have to find something to reinforce it with.

This target is meant for low power CO2, pump pistols, Crosman 1701P, etc. that make just a couple foot pounds of energy. Yes, I'm sure a .22LR or even a 1000fps pellet gun would shoot straight thru it. I use a 1701P and it hasn't damaged it a bit. Makes a great addition to my shooting wall. The included targets make clear holes with regular Crosman hollow points, like as if you're using a hole punch. I like shoot-n-c for outside, but man, this paper is great for score keeping. Most of the pellets drop into the catch, some land behind the target, on the bottom plate. Wish they all went in the catch area, but at least none escape. With the 100 included targets, it's a great deal for $15 not to have to pick pellets off the floor and have the wife find out I'm shooting pellets in the house, LOL.

This trap is made well with thick steel plates. It is very good for 10 m target practice. Although it is made of thick steel, when a pellet hits the center of the trap from magnum air rifle such as Diana RWS48 or Gamo Shadow Sports, the steel plate at the tip of cone is bent and deformed after a few shots. Noticing this, I have filled this pellet trap with 4 sticks (1 lb each) of Duct Seal (~$2.00 each) that is available at Home Depot or Lowes. After filling the cone with the Duct Seal, even with hundreds of pellets, pellets can penetrate only up to 3 inches or so. Also, we hear no metal noise when the pellet hits the target. If you are targeting with accurate guns, the face size 5.5" x 5.5" of this trap seems large enough to make a few small groupings, and you can have hours of target shooting enjoyment.

This thing is small!! Now, I am a good shot, but sometimes you have to sight in a scope and this thing makes it impossible. It is probably of if you are already sighted in, but otherwise it cannot be used for that purpose.

Not really for magnum airguns. Used the first one with a .25 PCP rifle, once, dinged it up pretty good. Second used for .177 SSP target pistols, no problems. Assembly not a problem, easy.

Had one of these for twenty years , still usable although now quite dented it does what it is intended to do , catch pellets in a safe way . Good product .

Todo muy bien

Trap is nice. Catch as many of the pellets. No complaints. Shooting from 45 ft away and a 4x scope is perfect.

Shot 50 .22 cal into it from 5 feet away. It caught all the pellets. Not a single one came out. The rear deflector plate started to bent upwards, Had to push it back down to protect behind it. Before i realized the deflector plate was pushed up, one of the pellet already hit the back part and dented it (no big deal though. The metal is strong enough to handle the shot. The photo shows the deflector plate after i bent it back down. Overall, great product does the job well.

If you are new at shooting, using an older bb gun or shooting at a range where you are sometimes 4 - 5 inches off centre this may not catch a bb/pellet. Am using with a pellet rifle which can use a range of pressures and thus a range of muzzle velocities...am concerned about vertical accuracy when sighting for different velocities - returned unit.