948-II 4 in 1 Hot Air Rework Soldering Iron and Desoldering Suction Tin Gun Station with Suction Pick Up Pen °F /°C

I've been a hobbyist my entire life and have been known to do a bit of soldering here and there, but as things get smaller and smaller, the tools become less and less useful. I eventually found myself needing to remove a chip from a microcontroller board to replace it and lacking the tools to do so.I could have just gotten a hot air rework station by itself and called it a day, but I realized my poor old soldering iron was getting a bit worn out so I decided I'd get one with a soldering iron too, and then I saw a video of someone using a desoldering sucker and knew I had to have one.Lucky for me, there's an option to get all three in one nice package. I didn't even realize the machine had the small suction grabber for pulling and holding chips when using hot air, definitely a bonus that I wasn't expecting.I've used it a lot by now, and wanted to do so before I put in a review.The soldering iron is excellent, it heats quickly and has absolutely never let me down, grab yourself a set of extra tips of different formfactors and you'll be good to go.The desoldering gun took some learning, and I managed to clog it up pretty bad a few times before I got good at it. The trick seems to be holding the suction down until the solder is pulled all the way to the back of the internal catching spring. Once I got the hang of it, I was using it to pull through-hole components in record time. As a bonus, it's also pretty darn good at cleaning up pads without having to use solder wick.The air gun is why I got it in the first place, and it did the job I got it for without any effort, removed the chip and replaced it within 10 minutes of getting the machine and I've used it dozens of times since. It's reliable, heats quickly, and has all the tips you need to put the heat exactly where it needs to go.The small suction cup wand that I didn't realize it included is pretty awesome, I didn't even realize a tool like this existed, with the right cup on it you can get a lock on a chip so tight it'll lift the entire board off the table if you pull hard enough. This makes it trivial to pull chips without having to use tweezers, and even works for reinstalling them. A small dab of flux can help secure the suction if things are a bit dry. I didn't know I wanted it, but I don't know if I can ever go back to not having one.Overall, 10 out of 10, I couldn't be happier with it. The extra components and usage of standard parts for things like iron tips and heat carts just makes things all the better when the time comes to replace consumables.

Received this yesterday, quickly and undamaged. Packing was pretty good and was double boxed. I read the manual cover to cover. It's not very long and worth doing. Fairly simple and written well. It took about 15-20 minutes to get it set up. I tinned the tips on both the iron and desoldering gun as directed. The iron warms quickly and temp seems accurate (didn't test yet but will). You can calibrate the displayed temp, which is useful.The desoldering gun performed similarly but took a lot longer to get to temp. The vacuum will not operate until up to temp, which is a good thing. The desoldering technique has a bit of a learning curve. Patience is required but, once you get it figured out, you'll never want to use wick or suction bulbs again. I used it on a scrape board for about a half hour(it's oddly satisfying) and had my first clog. A bit of a PITA to clear and clean but I will get it figured out over time. A bit more suction would be nice but there may be a fine line between maintaining temp and suction power.(guessing...)I have yet to try the heat gun as I rarely mess with SMDs but I'm optimistic. The "Channels" feature is a nice option. It is actually what I would call a "Preset" and should be a big time saver. There is a "sleep timer" feature for auto shut off as well. The solder and desolder cannot be used at the same time, which is not a deal breaker. I'll plug my old station into a separate outlet and have them both going if needed.I think this is a great unit for a hobbyist or part time fixer/maker, especially when you consider the cost. If I needed it to make a living, I would probably look at the more expensive, well known brands. Since I am a weekend warrior, this is perfect. My son is more of a SMD guy, so I'll update when he tries out the hot air and/or it develops an issue.

This soldering/desoldering station offers a convenient all-in-one solution for your soldering needs. Initially, there was confusion with the Fahrenheit preset, but once switched to Celsius, the performance improved significantly.While some users have experienced issues with the desoldering gun being slow to reach temperature and prone to jamming, following the manual's instructions can prevent these issues. Ensuring the gun reaches the recommended temperature and using the correct technique can lead to successful desoldering and clean joints.In a practical scenario of replacing a 7 pin header, the desoldering gun proved to be a time-saver, making the process more efficient and leaving clean holes for soldering. Overall, this station offers great value for its functionality and ease of use once you familiarize yourself with its settings and instructions.

I've owned and used this unit for about a month now. This unit is a nice improvement on previous models as it has a separate hookup for the iron, and the de-soldering iron. However, you can only have one turned on at a time. Meaning, if your using the iron, you can't be using the de-solder iron at the same time - which can be a pain sometimes, because you have to wait for it to reheat when you switch to the other iron. The de-solder iron works great for PCB use - I love it - be careful not to overheat your PCB with it or it will burn the trace right off. The Stand for the iron & de-solder iron is a single combined unit, that is kind of a pain - I wish there was a separate sand for each. The sand is made very cheap, and I have had to keep fixing it, as it keeps coming apart. They should have a stand for each unit. The controls are super easy to use, ONCE you ready the directions! When in de-solder mode, the suction won't turn on until it has reached the heat level you set. Also, there is a "Vacuum" button on the control panel - this button ONLY works when it is in SOLDERING mode, and it is for you to hook up a tube to the vacuum and use a suction cup to hold things like chips, while you solder them. The Vacuum button does nothing in de-soldering mode. The heat gun that is included works great too - but be careful, I have already burned my fingers, even being careful - its insane how hot it can get, but you can control the heat level. The heat gun will continue to run its fan even when you turn it off, unit it cools off enough - then it shuts down. The unit is made of nice quality steel and the control panel is also high quality controls - no plastic, except the on/off switches. Overall, I am happy with the unit, and I hope they include a separate stand for the de-soldering iron, and another one for the regular soldering iron, because the combined stand is a bit cumbersome and small.

awesome setup

I have no complaints at all about the Yihua. I've been using it for several months now and it has performed flawlessly. The soldering iron gets the most use. Temperature is accurate, heats up very quickly, maintains temperature properly during use.The desoldering gun works surprisingly well. I've had very mixed results with other brands. This one just works, although it does take a while to come up to working temperature.The hot air gun doesn't get a lot of use but when I've needed it I have had no problems with that either.Overall I like it a great deal and think it's good value for the money.

Excellent unit, air blower for heating shrink wrap tubing work well, takes a little time to heat up but has a nice shutdown safety feature when you turn the unit off the air in the gun keeps flowing until the unit is cool enough to not be a hazard. 3 Memory temperature preset one can used for various solder types and heat shrink types.Desolder gun has works very well, sucks the solder up with a pull of the trigger making it the easiest desolder process I've ever performed.You can NOT run both solder and desolder gun at the same time, this is most likely due to household current limits as the unit is already at 780 watt rating, trying to run air heater, desolder gun, and solder gun all at the same time will likely exceed 1500 watt (15Amp) rating of most 110v US house hold circuits and trigger home fuse. It would however have been nice if both could be plugged in and have a switch to enable One or the Other but not both desolder and solder at the same time.

Both the soldering and de-soldering tools work great. I don't have much experience with the hot air rework feature. It's so much better for removing components than trying to loosen them with just a soldering gun! I have successfully removed quite a few components without damaging them.

I've had this for awhile now, and no issues at all. Cheaper than other brands but this brand is well received and recognized overseas.

Equipo bastante completo cumple con excelencia ya que su funcionamiento es bastante completo y para mis tareas diarias es bastante bueno

A recommander

Excelentes productos...más de lo que esperaba

Buen producto, pero para desoldar le hace falta mas potencia de succión y de la pistola de aire caliente...