MICROJIG Matchfit Dovetail Clamp Pro Router Bit Kit, 1/2-inch Shank 14-Degree, Woodworking Track System Routing Tools, (DVC-1177K2)

These clamps are a great addition to my small shop. I've used them for sanding, joinery, tapering, joining, glue ups and keep discovering new uses. The clamps stay attached to my workbench, precisely where they are used. Using them as a mobile vice on the side of my work table has saved me hours during assembly of furniture. They've also saved me money. With a bit of spare plywood I've upgraded my mobile workbench and built jigs from the Micro Jig website. I rarely use other clamps and plan to purchase more to use with my miter saw and drill press. The slightly higher price is worth every penny when considering the versatility, web based support for this system. and the savings from purchasing an expensive work table, joiner or tapering jig. Just a great product, well thought out, that simplifies woodworking. Lesson learned, insure you accurately cut your tracks. Take extra time to insure you center your dovetail track on the relief track. I also have to say that Micro Jigs router bit is the way to go. Cut a relief track and the Final Cut is simple.

Excelente producto!! muy útil

These clamps are fantastic because they are so versatile. For example, you can make a super effective tapering jig in a couple of minutes that will handle 99% of needs for angled or exotic cuts. The same jig can then be used to extend a saw fence, or even be a surface for clamped glue ups. At the same time, they are surprisingly strong and very well made. These seem expensive, but quite honestly, I use them all the time.

These are so awesome to work with. The system is substantially cheaper than T-tracks. I know…t-tracks don’t need to be replaced. Well…your bench top will. Might as well save money and route the dovetails for these clamps. They are simple to use and pretty awesome. Make sure you understand how your router works and have a sturdy guide or you may end up with tracks that you cannot use. I had a small hiccup where my router slid away from the guide. This caused the groove to be too wide to allow good clamping. Not a big deal, I just slide past it or don’t clamp in that area.

This is extremely overpriced, however it does fulfill its intended purpose well. I've used the clamps in plywood, melamine with a particle board substrate, and solid softwoods so far, and they all work to a point. It's very easy to blow out in the particle board, which is to be expected, but if you use light pressure it will be fine. The plywood, poplar, and pine I've used them in hold much better. I used the accessories to make a stop block for my miter saw, and they are very hard to slide in the grooves. Tightening them down pulls the wedge up very high, and it gets stuck in the dovetail slot when you loosen it up, so you have to tap it down after. For the price, I think T-Track is a better permanent option. These are fantastic for jigs and other temporary solutions that you don't want to waste T-Track on. I modified some cheap clamps to fit the dovetail slots, much easier than you might think and it cost 1/3 or less the price of these clamps for the exact same function.

So many so many possibilities with the micro jig accessories. Their stuff is well made but over priced, so far it hasn't kept me from buying it.

Using these on a rip jig I built for my tables awesome. They work great at holding boards secure while running them through the saw.

I received this from my wife for Father’s Day and the setup is super simple Use a 1/4” spiral up cut bit to cut the relief then use the included dovetail bit, you can use your own dovetail bit however I wouldn’t. The one included has built In round overs that add to the durability of the dovetail as well as make it easier for clamps and accessories to slide in and out.

GREAT! Bit pricy but possibilities it opened are endless. Would be great (for this price) to get relieve bit too.

En el paquete venía un bisturí sumamente filoso fuera de la bolsa plástica que envolvía el producto , estaba adherido por un iman que mantenía unido los componentes del producto , pero dentro de la caja y al abrir la caja sufrí una herida en la mano. Dicho bisturí no es parte del producto que compre , a alguien se le quedó por negligencia ya la caja del producto venía dentro de la caja de Amazon . Gracias

Useless; a Festool collet would cost me another € 75,-

Ótimo e versátil kit para fixação de peças para trabalhar com as mesmas em serras e tupias, permite uma infinidade de configurações e projetos criados pelo próprio usuário.

Muy buen producto,una maravilla,pero...la fresa es de vástago de 12,7 q no lo pone en ningún sitio y yo he tenido q comprar el casquillo apostas para esa fresa,por lo demás genial