ONETWOFITWall Mounted Pull Up Bar with More Stable 6-hole design for Indoor and Outdoor Use, Maximum weight 440 Lbs OT103

Before I purchased this piece of equipment I looked for possibly 3 hours on amazon for all the products available and reading every single review.I finally chose to purchase this bar as I believed it would be the best based on cost, build, reviews.I was a bit skeptical after a few reviews said that the bar was not holding the users weight or they had issues with installation.I was trying to figure out if there were any issues with the assembly and the best way to attach to CMU block.The hardware that comes with the bar has concrete anchors, which being that I don’t have a hammer drill would be hell to install.I decided to purchase some 1/4” Tapcons At my local hardware store(2”-1/4” in length as I wanted to ensure it would grip on the CMU block).Even without a hammer drill, I set my drill to the hammer setting to install and didn’t take very long to have the bar installed.The drill bit should come with the Tapcons, but just in case to those who do not know what size drill bit to use, it’s a 3/16” concrete drill bit.The 1/4” Tapcons fit just fine and I have been using this bar for 2 Months about 3 times a week for all my calisthenics exercises.I’ve attached rings as well and I have not noticed any issues with the build of the bar.I am 230 lbs. and the bar is solid as can be.No issueA with bowing or bending.Great Product!

This is sturdy. Assembling it was easy. Installing is going to be completely up to you. Directions are unintelligible. The posts and holes on this are about 19 inches on center, so clearly wider than 16” studs. I knew that when I bought it. I didn’t have the width to buy a model with on-stud brackets Because those tend to be 32 inches wide or more. This one fit my space. As you can see by my pics, I built a 2x4 stringer rigging and attached those to the studs with lag bolts. I used 3/8” x 5” lags and washers. Then I attached the unit to the 2x4s using 3/8” x 2” lags and washers. This might be slight overkill but I don’t want to rip this out of the wall when I’m doing pull-ups. I am 225lbs and it did not flinch with me using it. So far so good. My son who is less than 100lbs will have no problems. Obviously, find the center of your studs. It’s a little bit of a puzzle to figure out how to get all of this to line up and to be level, but if you have hung things like TVs on the wall, you’ll be fine. If you’ve never hung anything heavy before, maybe consider consulting with a friend or relative who has. There are lots of videos out there to help too. Definitely need a good wratchet, preferably with a long extension to help with leverage when cranking the five inch lags. Also, this provides a good anchor for the various strength band attachments.

The bar is actually really great and very sturdy! Mounting was easy as well! Hanging a heavy bag even worked great. The downsides I'll have to say is the bar length for wide grips seems a bit too long and wide grip pull ups can be a bit risky for shoulder health. Or maybe because my size is average and could be fine for being taller folks. Secondly it'd be nice if there was more rubber grip paddings on the other handles near the wide grips for doing regular pull ups. Third, I think the rubber grips in the middle should've been much tighter as they tend to slip around when dropping and the grips misalign. Fourth, it was delivered safely but there was a slight bent on the flat steel to mount it making it bit odd to measure and straighten the bar, and fifth the six screws aren't too great for mounting against the wall so you may need better tools than the ones already given incase the wall type you have isn't suitableOverall the quality is good!

The pullup bar is exactly as pictured and works perfectly. I would probably widen it a bit if i had that option so i could grip just a bit wider right where the crossmembers attach to the pullup bar, but I can't complain at all because it's exactly as pictured, sturdy as a dumptruck and absolutely gets the job done.

This is very sturdy and heavy duty. It took some time for my husband to install as instructions not very clear and when he got it installed it was crooked, so he had to use some shims to level it out. Not sure if that was due to the wall itself or the unit. He likes being able to just hop up and do some pull-ups in the garage and not have to drive to the gym.

This works well as long as you bring you own backboard and fasteners. The mounting holes are 19” apart to if you have 16 on center walls you can’t mount it direct to the wall. One way around this is to use 2x6 lumber and fix it to the studs and then screw the pull up bar to it. You can also use two layers of 3/4 plywood to serve the same purpose. Either way you have to get your own fasteners.You will also need a 24” clamp if you want the mounting plate to be at 90 straight as they are not after assembly.Overall it took me about 4 hours and a trip to the hardware store to get it mounted to the wall.

Assembled it, then mounted it to the wall using the supplied Concrete Expansion anchors. The entire thing ripped out of the wall the moment I put any of my weight on it. I'm going to have to go get some better anchors to replace the crap ones that they supplied. Once it is sturdy I will write a proper review. Giving 3 stars because it seems like a legit piece of training equipment, just cheaped out on anchorsUpdate: Mounted the piece with proper 1/2" anchors from the hardware store. This thing is sturdy as a hell. Handles the heavy bag pretty well, but had to remove the chain and swivel due to the low ceiling in my garage. Still a great product that does everything i need it to do. Upgraded review to five stars.

Missing one of the grips.Returning it.