HandAll Beavertail Rubber Grip for Glock 17, 19X, 22, 45 | Also Fits 17L, 17MOS, 18, 20, 22, 24, 31, 34, 34MOS, 35, 24, 31, 35MOS, 37, 40, 41, 45, 47

Perfect fit for S&W M&P 22 Magnum! Had it on in five minutes. Boil it in water for 3 minutes. Dry. Windex gun grip and inside Hogue grip. Start it on Beaver Tail and work it on. Back and forth. You’ll get. Add Windex if you need to. Great grip!

Great fit! Hard to install? Maybe if you don't have strong hands. Love the feel of my Glock 17 now. Before it was too skinny for my hand...now it fits like a glove!

Best thing that ever happened to my beloved pistols. These grips increase control and comfort, resulting in better accuracy for me.

Its a little difficult to get on but it's worth the effort. This fits my hand perfectly, and gives more control and better grip when I go to the range.

I’ll give it a solid 4 altogether! It is really hard to get it on, so I had to watch a few videos to figure out the easiest and best way to help it go because it was hard getting it to stretch around the handle- After attached the hand grip was perfect! It’s so natural feeling in your hand. It’s thick and easier to hold. It looks so good! The size is perfect!

Love this grip! It’s not that hard to put on. I put it in hot water for 5 minutes, dried it off, stretched it out by hand a bit then pulled it onto the butt of my pistol. Fits tight and I really like the finger grooves and softer feel of the grip.

The grip is too long for a glock 19. The grip overlaps the handle and it will leave slack that will get in the way when you are doing a magazine exchange. I had to roll up at the bottom of my grip sleeve so it will not get in the way of me exchanging my magazines. The other option is to cut off the extra slack with a scissor so it will not get in the way of your magazine exchange. I was able to get the grip sleeve all the way up my glock 19 handle with a flat head screwdriver in less than 5 minutes without putting it in water. Please be careful not to puncture your grip sleeve cover with the flat head screwdriver as you try to get it on because I didn't to mine but I have no other issues other than the extra slack.

So for the price this is an amazing item. I am 6'3" and have corresponding sized hands. My 9mm Glock 45 fits my hands well, but I still wanted a little more grip. This was the perfect solution. Grip feels much more solid and controlled. Installation is not easy at all. But if you work smarter you won't need to work harder. I used the boiling water and windex route. First, pour boiling water into a bowl and let the grip soak in it for 30+ seconds. While it is soaking spray the grip with Windex and don't be stingy, it should be dripping off. I installed it with the slide removed. Using tongs pull the grip out of the water, shake loose any residual moisture, and install as quickly as possible. I did not need to use the two plastic strips that they suggest, but it did take a few attempts to get the first part of the Hogue grip over the Glock grip. Once the first part is attached quickly slide it up using any means you can. The windex gets super slippery so I kept a towel nearby to dry off my hands during the process. I also re-dipped the Hogue into the hot water during the process. The trick is to be prepared and to move quickly but efficiently. Heat and windex are your friends in this. Be patient and deliberate and the install won't be easy, but will be possible.

G17gen5へ装着予定でしたが、私のやり方が悪いのか全然入りません！

Love it! Fit perfect and feels very nice in the hand.

Nice grip

fits perfect on a Gen5 just dip it in hot water, use a little windex on the frame and it will install perfectly

Was shipped with a hole in the rubber...