HitLights LED Strip Lights, 4 Pre-Cut Waterproof RGB Small LED Light Strip Kit Dimmable Color Changing SMD 5050 LED Tape Light with RF Remote, UL-Listed Power Supply and Connectors for TV Bedroom Home

I purchased these LED strips to accent a new PC I built recently, and they have done an excellent job so far. I did have a minor issue with the adhesive not holding on vertical surfaces, so I contacted the seller about the issue. They were very easy to work with and helped me get the issue resolved without any hassle on my part. Overall, 5/5 would purchase again.Pros: The strips are sized perfectly for adding accent light to a PC. Having 4 one foot sections is way easier to work with than trying to use a single long strip or building/soldering them yourself. I tried the remote control through the glass side panel of my case and it worked perfectly. I currently have the lights plugged into the Aura RGB header on the motherboard to control them that way. This also works without issue. This kit includes everything you would need to wire a PC up for lighting including enough extension cables to wire everything in so it looks nice.Cons: As I said, I had a minor issue with the lights not holding on vertical surfaces. This was solved by using some double sided mounting tape, which has held well. I am not entirely sold on using the included clips. The adhesive does seem stronger, but it created a 'speed bump' looking bubble over where the clip was, causing a part of the strip itself to lose contact with the case. These bumps were always the first place to lose their grip before I used the double sided tape.Other: I also have some LED lights around my desk that has been installed for a while. It is the same type that is sold in 15 ft rolls that you can find all over on Amazon. The wiring for the LED strips I already had and these were different, so that when I tried to wire them into a single controller and power supply the blue and green channels were reversed. So if I had full green on my old LED's it would have full blue on the new ones inside the case. This isn't something that the seller can control, nor is it something I thought to ask before purchasing, but it is something to consider. Oddly enough, because only the blue and green channels are reversed, full red works fine. I was able to solder in a wire a crossover for the blue and green where the new LEDS are wired in and after that the colors matched without issue.

Installed these into a display cabinet to provide light. Was very easy to attach and install. I had to drill a bit larger of a hole (1/2 inch) to insert the attaching male/female wire connector - but a very minor issue. Just make sure the small arrows line-up. You can space the lights out or place them together per your need. I put the lights together and used the extra connectors so that I did not require an extension as that plus the 6 foot electrical line from the 110 volt power adaptor gave me plenty of line to my electrical outlet behind the cabinet. These are very cool. They use little electricity, are very bright, light weight and the adhesion works perfect. Make sure the alignment is good as the adhesive backing sticks well. You can remove and replace, but I tried to get it right the first time and measured so that I just peeled and stuck to the top of the inside of the cabinet. Th BEST feature along with the multiple light options and multiple colors is the RF (radio frequency) transmitter. This allows off/on operation and adjustment without a direct line-of-sight to the light sensor control. I can turn on and adjust without facing a certain director or have to expose the sensor which makes installation very easy and cosmetically much better. Used for a couple of weeks no with no problems. I will be purchasing at least two more sets for another project. Excellent product.

Vibrant lighting...good adhesive stripWorks well...connections are a bit difficult to snap together but once you do it's game on...very simple and amazing...anyone could install this without professional help...

Pretty much what you would expect from modular RGB leds. easy to installPros:- The usual remote but it functions well.- Easy to customize- Basic selection of connection work- had some Clips included though I wasn't able to use on my scrap wood project.Cons / could be better:- Would have been nice if the clips came with a hole drilled so you could screw/nail if you don't want to trust the adhesive.- could have seen a split connection included to vastly increase functionality. Yes its modular you can't run four separate lines from the unit which limits its usefulness to a straight line with added gaps effectively .- A bit dim in a lit room if used for accent during daylight - like you cant see it dim.- Very stiff strips if flat against a surface there is so much coating on the strips making a slight curve is a challenge if not impossible (why I wasn't able to use the adhesive and had to get something else to hold the on with) ended up mounting on edge just to get any kind of bend in there.- Bulky in most areas, flimsy where it counts. The connections a just 4 bits of hard wire in a miniscule plastic strip. just putting it together you know this is a future failure point , hell they were popping out just trying to get the clips on and I was on a flat desk, wouldn't try it upside down on an installed fixture.Summary:I'd buy it again but probably look for something with more flex unless just straight under cabinet mounting. Definitely not a suitable for case mods unless your case is flat piece of plywood.