Bo Nash 19-Inch-by-59-Inch IronSlide 2000 Ironing Board Cover, Silver

Ironing is such a chore. It's even more difficult when the ironing board cover is loose and bunches up or too thin that the mesh from the board underneath shows up on the clothes. After much research, we decided to bite the bullet and get the bonash after reading several reviews and watching the videos on their website. What a great decision. Installation can be a little tricky so watch the video for the tips. Other than that, my Rowenta iron glides over the clothes without any issues.. padding is excellent and although ironing is still a chore, it's much more pleasant when you have a good cover on.

Did does not make wrinkles in your clothes when you iron on it like the cloth kind can. It also helps by reflecting the heat to iron faster. Leave it long around all sides to tuck under then cut it before you attach it or your scissors will stick and not cut.

I had thought this was an easy ironing board to just slide onto my ironing board. I read the directions, all of them, and started cutting up my board flannel. Then I had to apply their foam pad and had to cut that also. Then I had to peel back 2” from the square end and place that on the square end. That’s when my troubles started. I tried and tried to get that 2” in the proper spot and leave a few inches on each side to wrap under the metal top of my board. I realized I was off center so I tried to get it centered, but now the foam was sticking, and then their ironing board fabric was sticking to itself. I only had another 50” to go…. I had foam everywhere. I couldn’t get the adhesive apart, and now it was sticking everywhere. I had tons of cut foam on the floor and adhesive on my hands, so the foam was now sticking to my hands. There is so much adhesive pieces and peel away (haha) backing all over the chair and floor. This stuff does NOT sweep up. You have to get down and peel off sticky guck from the floor. What a MESS! I am a very patient person and figured that I could do this project with ease as described in the instructions. You try handling 60” of unwieldy stiff silver cover with other foam on the bottom. I don’t think my hubby and I could have done this.. it would have turned into a heated argument, to say the least. So, I give this product an overwhelming F for Failure.

I have been looking for an ironing board cover for my extra large ironing board. This fit the bill perfectly.The metallic fabric will make ironing much easier now. I was able to position it and then peel and stick the material starting on the wide end of the board. Working about 4 - 6 inches at a time it went on effortlessly. I did not cut the narrow end until I was within a foot from the end. I allowed about 2" extra and worked the excess around the curve making tiny gathers. No problem at all and no wrinkles. It took about two minutes.

It was nothing short of a painful experience to do the pad trimming and the measurements are not accurate. It really takes two people to apply the pad that is stuck onto the ironing board. The pad also requires trimming and what a mess with the good scissors sticking to the pad......not a fun experience to say the least....yikes....

Yes...this was exactly what I was looking for in an ironing board cover --and what I could not find to purchase locally. I used this cover on top of the cotton ironing board cover that came with my new "over the door mount" ironing board since I don't like cotton ironing board covers. IF you READ and FOLLOW the directions for installing this ironing board cover (which is important and did take a bit of time) there is absolutely no reason not to get a good fitting, slip-proof ironing board cover that actually makes ironing easier. This fabric cover is adhesive based, so take your time to apply it correctly. The heat reflective properties of the cover are wonderful and make ironing easier (not exactly a pleasure, but certainly easier :) .

Expensive for an ironing board cover and can be tricky to install but well worth the money and effort if you iron a lot. I have been sewing for many years and I consider my iron and board to be as important a tool as my sewing machines. This made my board more efficient and made ironing bulky or difficult fabrics far easier. I bought a similar cover 15 years ago and fell in love. It lasted that long! So when it started wearing out, I bought this as a replacement. A must have for seamstresses!

Nice board cover that takes a bit of effort to install properly. Recommend watching the YouTube video on installation to help you see the steps. Not difficult, but a bit sticky and messy. Once installed, it seems to work well. Happy with it and glad it appears to be durable.